***Bearclaw's Gift Thread MAY 2009***

[Bman212121]

52

[bob saget]

:headexplode:

[bob saget]

53

You mean the ones outside of the case?

no i mean like motherboard power...etc.

[Bman212121]

51

I ran some stuff alongside of the board, but I don't really have anything traveling underneath it.

[Bman212121]

no i mean like motherboard power...etc.

50

Well there is not enough room underneath the board standoffs for that. But some cases do have holes you can come out of to hide it a little.

[bob saget]

:headexplode:

my head is round.

[Bman212121]

49

In the stacker there really isn't anyway I could hide those wires as it's only 3 or 4" on the frontside anyway. The 8 pins for the CPU connector runs alongside of the board and slightly under the edge so it's out of view.

[bob saget]

51

I ran some stuff alongside of the board, but I don't really have anything traveling underneath it.

thats how mine is.

yea i was talking about the holes, some people run their wires out through that.

[Bman212121]

48

Let me find a pic of that case, I believe there were some in the lapping thread.

[bob saget]

kk

[Bman212121]

thats how mine is.

yea i was talking about the holes, some people run their wires out through that.

47

You could if your connectors were far enough along. That big 24 pin connector doesn't bend so easy though. If you had a dremel or a hole saw you could even cut a hole, then get some of the rubber O ring stuff to cover the edges so you don't cut anything.

[Bman212121]

46

On my stacker it has like 2 bars for the 5 1/4" bays, I hide some of the wires down the backside of that. One thing for me is I like to keep everything functional because I tend to work inside of the case a lot. So if I were to stuff the wires through the board it would be a pain to work on the case.

[bob saget]

oh i see.

u has pics?

[Bman212121]

46

Personally I think it looks just as good if they are in a straight line next to the board, all sleeved up and tied neatly. You can see the wires but they look clean and are much easier to manage.

[Bman212121]

45

*looks for pics*

[bob saget]

46

Personally I think it looks just as good if they are in a straight line next to the board, all sleeved up and tied neatly. You can see the wires but they look clean and are much easier to manage.

yea i know what you mean.

[Bman212121]

44

I didn't have them shoved all the way back in neatly, but you get the idea.

http://i42.tinypic.com/33tp3r8.jpg

[Bman212121]

43

http://i42.tinypic.com/or42h2.jpg

[bob saget]

gr8

[Bman212121]

42

[Bman212121]

gr8

41

TY :)

[Bman212121]

40

I still have an IDE DVD drive in there, but it's using the rounded cable, which doesn't look too bad. Sata would be even easier to hide though.

[Bman212121]

39

Considering what's in there it looks pretty decent. 2 GPUs, 2 HDDs, a DVD drive, an X-Fi with front panel. (I sleeved that sucker as well, just need to be really careful with that guy.)

[Bman212121]

38

If you look really closely to behind the bottom GPU (Actually top in the pic) between that and the hard drive there is a sleeved wire going through there. That is the front panel connectors. It used to stick out really badly because it's a multicolored ribbon cable. Now with the sleeving you don't even notice it. it's not so much that it's gone, it just doesn't draw any attention now.

[Bman212121]

37