nV News Forums

 
 

nV News Forums (http://www.nvnews.net/vbulletin/index.php)
-   NVIDIA Linux (http://www.nvnews.net/vbulletin/forumdisplay.php?f=14)
-   -   ConnectedMonitors and DisplayPort (http://www.nvnews.net/vbulletin/showthread.php?t=161305)

prefect42 04-07-11 09:47 AM

ConnectedMonitors and DisplayPort
 
2 Attachment(s)
I have a CentOS 5.5 machine (260.19.44) with a pair of Quadro FX 3800 cards. Connected are two monitors via DVI, and two monitors via DP. If I turn all the monitors off, and restart X, only the two DVI monitors are configured, and the two DisplayPort monitors are disabled.

This is true even if I use:

Option "ConnectedMonitors" "DFP-0, DFP-3"

Any suggestions as to how I can make this work such that there are always four monitors enabled irrespective of how many are currently powered on?

I have an ugly hack workaround but it's not a perfect solution... Wire in the monitors with USB cables, and use udev to trigger an X restart when a monitor is powered on and nvidia-settings says there are less than four monitors ;)

There really is a somewhat valid reason why I want this...

jh

danix 04-08-11 03:02 PM

Re: ConnectedMonitors and DisplayPort
 
I believe DisplayPort link training requires active participation from both the source and the sink, so I'm not sure if this can be made to work if the display won't engage in link training when it's off.

Have you tried passive DP->DVI dongles?

Xevious 04-09-11 03:56 AM

Re: ConnectedMonitors and DisplayPort
 
Sounds like what you need is a 'dvi detective' except a displayport version. Unfortunately I don't know of any that exist =(

prefect42 04-12-11 03:16 AM

Re: ConnectedMonitors and DisplayPort
 
Quote:

Originally Posted by danix (Post 2416234)
Have you tried passive DP->DVI dongles?

These are only good for low resolutions as far as I'm aware (single link DVI). I'm running 2560x1440@60Hz so need dual-link. Active DP-DVI dongles are about 80 quid a pop. These monitors form part of a number of display walls, so I'd need quite a few.

danix 04-14-11 12:31 PM

Re: ConnectedMonitors and DisplayPort
 
Yes, unfortunately passive dongles only support single link. To do what you want with active dongles, I'm pretty sure the dongle would have to allow link training even if a display device isn't connected. I'm not sure if there are any existing active dongle designs that do this.

Xevious 04-14-11 12:39 PM

Re: ConnectedMonitors and DisplayPort
 
Quote:

Originally Posted by prefect42 (Post 2417297)
These are only good for low resolutions as far as I'm aware (single link DVI). I'm running 2560x1440@60Hz so need dual-link. Active DP-DVI dongles are about 80 quid a pop. These monitors form part of a number of display walls, so I'd need quite a few.

I bought one of the dell OEM (bizlink) ddual link DVI active adapters for pretty cheap from a seller in texas for ~$50 shipped:

http://cgi.ebay.com/Bizlink-DisplayP...item415711c342

Found this seller in the UK selling them pretty cheap too:

http://cgi.ebay.com/BizLink-DisplayP...item256244fa54

prefect42 04-14-11 12:49 PM

Re: ConnectedMonitors and DisplayPort
 
Quote:

Originally Posted by Xevious (Post 2418391)
Found this seller in the UK selling them pretty cheap too:

http://cgi.ebay.com/BizLink-DisplayP...item256244fa54

Many thanks for the link, that is much cheaper than I'd found. Would this *definitely* solve the problem? That is, without a powered on monitor attached but with this I'd be able to force it into thinking it did?

jh

Xevious 04-14-11 12:51 PM

Re: ConnectedMonitors and DisplayPort
 
Quote:

Originally Posted by prefect42 (Post 2418395)
Many thanks for the link, that is much cheaper than I'd found. Would this *definitely* solve the problem? That is, without a powered on monitor attached but with this I'd be able to force it into thinking it did?

jh

Hard to say for sure, you would have to buy one and test it.

That + a DVI detective I would say certainly would solve the problem. I would say its likely but not for sure in this case.

prefect42 04-14-11 12:53 PM

Re: ConnectedMonitors and DisplayPort
 
Quote:

Originally Posted by danix (Post 2418384)
Yes, unfortunately passive dongles only support single link. To do what you want with active dongles, I'm pretty sure the dongle would have to allow link training even if a display device isn't connected. I'm not sure if there are any existing active dongle designs that do this.

If I was running a newer X server, would XRandR be able to dynamically add the display back in? That way I could have a udev trigger that just seamlessly rearranged the display.

prefect42 04-14-11 12:56 PM

Re: ConnectedMonitors and DisplayPort
 
Quote:

Originally Posted by Xevious (Post 2418396)
Hard to say for sure, you would have to buy one and test it.

That + a DVI detective I would say certainly would solve the problem. I would say its likely but not for sure in this case.

Sure, I was just thinking along similar lines. It was much simpler when I built this with DVI (apart from the weight of 28 3-5M DVI leads...).

jh

danix 04-15-11 02:31 PM

Re: ConnectedMonitors and DisplayPort
 
Quote:

Originally Posted by prefect42 (Post 2418398)
If I was running a newer X server, would XRandR be able to dynamically add the display back in? That way I could have a udev trigger that just seamlessly rearranged the display.

The NVIDIA X driver only supports XRandR up to version 1.1, which I don't think has this functionality.

However, you could probably wire up your udev trigger to an NV-CONTROL client that does this.


All times are GMT -5. The time now is 11:46 PM.

Powered by vBulletin® Version 3.7.1
Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.
Copyright 1998 - 2014, nV News.