nV News Forums

 
 

nV News Forums (http://www.nvnews.net/vbulletin/index.php)
-   NVIDIA Linux (http://www.nvnews.net/vbulletin/forumdisplay.php?f=14)
-   -   forcedeth problems. (http://www.nvnews.net/vbulletin/showthread.php?t=84319)

chris_king 01-15-07 12:58 PM

forcedeth problems.
 
amd system.

modinfo forcedeth
filename: /lib/modules/2.6.13/kernel/drivers/net/forcedeth.ko
parmtype: max_interrupt_work:int
parm: max_interrupt_work:forcedeth maximum events handled per interrupt
parmtype: optimization_mode:int
parm: optimization_mode:In throughput mode (0), every tx & rx packet will generate an interrupt. In CPU mode (1), interrupts are controlled by a timer.
parmtype: poll_interval:int
parm: poll_interval:Interval determines how frequent timer interrupt is generated by [(time_in_micro_secs * 100) / (2^10)]. Min is 0 and Max is 65535.
parmtype: msi:int
parm: msi:MSI interrupts are enabled by setting to 1 and disabled by setting to 0.
parmtype: msix:int
parm: msix:MSIX interrupts are enabled by setting to 1 and disabled by setting to 0.
parmtype: speed_duplex:int
parm: speed_duplex:PHY speed and duplex settings. Auto = 0, 10mbps half = 1, 10mbps full = 2, 100mbps half = 3, 100mbps full = 4, 1000mbps full = 5.
parmtype: autoneg:int
parm: autoneg:PHY autonegotiate is enabled by setting to 1 and disabled by setting to 0.
parmtype: scatter_gather:int
parm: scatter_gather:Scatter gather is enabled by setting to 1 and disabled by setting to 0.
parmtype: tso_offload:int
parm: tso_offload:TCP Segmentation offload is enabled by setting to 1 and disabled by setting to 0.
parmtype: mtu:int
parm: mtu:MTU value. Maximum value of 1500 or 9100 depending on hardware.
parmtype: tx_checksum_offload:int
parm: tx_checksum_offload:Tx checksum offload is enabled by setting to 1 and disabled by setting to 0.
parmtype: rx_checksum_offload:int
parm: rx_checksum_offload:Rx checksum offload is enabled by setting to 1 and disabled by setting to 0.
parmtype: tx_ring_size:int
parm: tx_ring_size:Tx ring size. Maximum value of 1024 or 16384 depending on hardware.
parmtype: rx_ring_size:int
parm: rx_ring_size:Rx ring size. Maximum value of 1024 or 16384 depending on hardware.
parmtype: tx_flow_control:int
parm: tx_flow_control:Tx flow control is enabled by setting to 1 and disabled by setting to 0.
parmtype: rx_flow_control:int
parm: rx_flow_control:Rx flow control is enabled by setting to 1 and disabled by setting to 0.
parmtype: dma_64bit:int
parm: dma_64bit:High DMA is enabled by setting to 1 and disabled by setting to 0.
parmtype: wol:int
parm: wol:Wake-On-Lan is enabled by setting to 1 and disabled by setting to 0.
parmtype: tagging_8021pq:int
parm: tagging_8021pq:802.1pq tagging is enabled by setting to 1 and disabled by setting to 0.
author: Manfred Spraul <manfred@colorfullife.com>
description: Reverse Engineered nForce ethernet driver
license: GPL
vermagic: 2.6.13 SMP K8 gcc-3.3
depends:
alias: pci:v000010DEd000001C3sv*sd*bc*sc*i*
alias: pci:v000010DEd00000066sv*sd*bc*sc*i*
alias: pci:v000010DEd000000D6sv*sd*bc*sc*i*
alias: pci:v000010DEd00000086sv*sd*bc*sc*i*
alias: pci:v000010DEd0000008Csv*sd*bc*sc*i*
alias: pci:v000010DEd000000E6sv*sd*bc*sc*i*
alias: pci:v000010DEd000000DFsv*sd*bc*sc*i*
alias: pci:v000010DEd00000056sv*sd*bc*sc*i*
alias: pci:v000010DEd00000057sv*sd*bc*sc*i*
alias: pci:v000010DEd00000037sv*sd*bc*sc*i*
alias: pci:v000010DEd00000038sv*sd*bc*sc*i*
alias: pci:v000010DEd00000268sv*sd*bc*sc*i*
alias: pci:v000010DEd00000269sv*sd*bc*sc*i*
alias: pci:v000010DEd00000372sv*sd*bc*sc*i*
alias: pci:v000010DEd00000373sv*sd*bc*sc*i*
alias: pci:v000010DEd000003E5sv*sd*bc*sc*i*
alias: pci:v000010DEd000003E6sv*sd*bc*sc*i*
alias: pci:v000010DEd000003EEsv*sd*bc*sc*i*
alias: pci:v000010DEd000003EFsv*sd*bc*sc*i*
alias: pci:v000010DEd00000450sv*sd*bc*sc*i*
alias: pci:v000010DEd00000451sv*sd*bc*sc*i*
alias: pci:v000010DEd00000452sv*sd*bc*sc*i*
alias: pci:v000010DEd00000453sv*sd*bc*sc*i*



00:0a.0 Ethernet controller: nVidia Corporation CK804 Ethernet Controller (rev a3)
Subsystem: Tyan Computer: Unknown device 2865
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0 (250ns min, 5000ns max)
Interrupt: pin A routed to IRQ 19
Region 0: Memory at febfc000 (32-bit, non-prefetchable) [size=4K]
Region 1: I/O ports at e400 [size=8]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable+ DSel=0 DScale=0 PME-




ifconfig eth1

eth1 Link encap:Ethernet HWaddr 00:E0:81:59:BE:03
inet addr:10.0.0.10 Bcast:10.255.255.255 Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:6 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
Interrupt:19 Base address:0x4000

Settings for eth1:
Supported ports: [ MII ]
Supported link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
1000baseT/Full
Supports auto-negotiation: Yes
Advertised link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
Advertised auto-negotiation: Yes
Speed: 100Mb/s
Duplex: Full
Port: MII
PHYAD: 1
Transceiver: external
Auto-negotiation: on
Supports Wake-on: g
Wake-on: d
Link detected: yes
root@dev3:/usr/src/linux#



ping 10.0.0.10
PING 10.0.0.10 (10.0.0.10) 56(84) bytes of data.
64 bytes from 10.0.0.10: icmp_seq=1 ttl=64 time=0.027 ms

ping 10.0.0.2
PING 10.0.0.2 (10.0.0.2) 56(84) bytes of data.

--- 10.0.0.2 ping statistics ---
1 packets transmitted, 0 received, 100% packet loss, time 0ms


internal vlan, cant get it to ping out.. any ideas???

netllama 01-15-07 01:04 PM

Re: forcedeth problems.
 
http://www.nvnews.net/vbulletin/showthread.php?t=75597

chris_king 01-15-07 01:18 PM

Re: forcedeth problems.
 
didnt work.

chris_king 01-15-07 01:20 PM

Re: forcedeth problems.
 
and im using the newest from their website that, that package came from.

netllama 01-15-07 01:23 PM

Re: forcedeth problems.
 
What's the output from "ethtool -i eth1" and "route -n" ?

chris_king 01-15-07 01:31 PM

Re: forcedeth problems.
 
i pasted ethtool.. but here is again.


Settings for eth1:
Supported ports: [ MII ]
Supported link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
1000baseT/Full
Supports auto-negotiation: Yes
Advertised link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
Advertised auto-negotiation: Yes
Speed: 100Mb/s
Duplex: Full
Port: MII
PHYAD: 1
Transceiver: external
Auto-negotiation: on
Supports Wake-on: g
Wake-on: d
Link detected: yes

netllama 01-15-07 01:33 PM

Re: forcedeth problems.
 
That isn't the output from the command I requested.

chris_king 01-15-07 01:36 PM

Re: forcedeth problems.
 
ethtool -i eth1
driver: forcedeth
version: 0.56
firmware-version:
bus-info: 0000:00:0a.0


sorry.. overlooked the -i

netllama 01-15-07 01:39 PM

Re: forcedeth problems.
 
You still did not provide the output from both of the commands that I noted. Also, forcedeth-0.56 is not the latest version as noted in the URL I referenced.

chris_king 01-15-07 01:42 PM

Re: forcedeth problems.
 
and nothing big on the route.
10.0.0.0 * 255.255.255.0 U 0 0 0 eth1

chris_king 01-15-07 01:43 PM

Re: forcedeth problems.
 
from the download in the link
#define FORCEDETH_VERSION "0.56"
#define DRV_NAME "forcedeth"

netllama 01-15-07 01:47 PM

Re: forcedeth problems.
 
Sorry, the attachment is out of date. Please see the URL in the post.

What kind of motherboard are you using?
Which Linux distribution?
What kind of network topology are you using?


All times are GMT -5. The time now is 07:17 AM.

Powered by vBulletin® Version 3.7.1
Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.
Copyright 1998 - 2014, nV News.