nV News Forums - 2nd NIC is off on Asus M2N-SLI Deluxe (nForce 570 SLI MCP)

nV News Forums (http://www.nvnews.net/vbulletin/index.php)

- General Linux (http://www.nvnews.net/vbulletin/forumdisplay.php?f=27)

- - 2nd NIC is off on Asus M2N-SLI Deluxe (nForce 570 SLI MCP) (http://www.nvnews.net/vbulletin/showthread.php?t=89621)

2nd NIC is off on Asus M2N-SLI Deluxe (nForce 570 SLI MCP)

Hello,
I have a problem with the second of my two on-board NICs on the Asus M2N-SLI Deluxe (chipset: nForce 750 SLI MCP): It is completely dead after booting Linux.

To reproduce the problem:
1) Power supply off.
2) Power supply on: both NICs get GBit link (LEDs are on).
3) System power on, waiting for GRUB to load: both NICs still have link.
4) Booting kernel: upon loading of forcedeth, both NICs get turned off (LEDs off).
5) somewhat later in the boot sequence: first NIC gets link again, but second link never comes up

This could be reproduced with forcedeth versions 0.56, 0.59 and 0.60, in kernels 2.6.18, 2.6.20 and 2.6.21-rc6 (all amd64). The processor is an Athlon64 X2 5000+. I tried Asus BIOS versions 0404 and 0903.

On some very rare occasions albeit, the second NIC "just worked". Once after cold boot and another time (surprisingly) after unplugging and replugging the network cable. (This was luck. Switching cables between the NICs does not help, usually, the problem stays with the 2nd NIC.)

Maybe another interesting point: when doing
6) reboot: the 2nd NIC stays off, even during initialisation of BIOS
Cold power off is necessary to get the 2nd NIC to work during BIOS initialisation.

Code:

# ethtool -i eth1

driver: forcedeth

version: 0.60

firmware-version:

bus-info: 0000:00:08.0

# ethtool eth1

Settings for eth1:

        Supported ports: [ MII ]

        Supported link modes:   10baseT/Half 10baseT/Full

                                100baseT/Half 100baseT/Full

                                1000baseT/Full

        Supports auto-negotiation: Yes

        Advertised link modes:  10baseT/Half 10baseT/Full

                                100baseT/Half 100baseT/Full

                                1000baseT/Full

        Advertised auto-negotiation: Yes

        Speed: 1000Mb/s

        Duplex: Full

        Port: MII

        PHYAD: 1

        Transceiver: external

        Auto-negotiation: on

        Supports Wake-on: g

        Wake-on: d

        Link detected: yes

# ethtool -i eth2

driver: forcedeth

version: 0.60

firmware-version:

bus-info: 0000:00:09.0

# ethtool eth2

Settings for eth2:

        Supported ports: [ MII ]

        Supported link modes:   10baseT/Half 10baseT/Full

                                100baseT/Half 100baseT/Full

                                1000baseT/Full

        Supports auto-negotiation: Yes

        Advertised link modes:  10baseT/Half 10baseT/Full

                                100baseT/Half 100baseT/Full

                                1000baseT/Full

        Advertised auto-negotiation: Yes

        Speed: Unknown! (65535)

        Duplex: Unknown! (255)

        Port: MII

        PHYAD: 1

        Transceiver: external

        Auto-negotiation: on

        Supports Wake-on: g

        Wake-on: d

        Link detected: no        

# ethtool -t eth2

The test result is FAIL

The test extra info:

link      (online/offline)       1

register  (offline)              0

interrupt (offline)              0

loopback  (offline)              0

Help would be greatly appreciated!
Regards,
extensive2

Re: 2nd NIC is off on Asus M2N-SLI Deluxe (nForce 570 SLI MCP)

your dmesg & ethtool info is a bit out of sync... (or do you remap the eths?)

dmesg:
eth0: forcedeth.c: subsystem: 01043:8239 bound to 0000:00:08.0
eth1: forcedeth.c: subsystem: 01043:8239 bound to 0000:00:09.0
eth2: (3Com PCI 3c905B Cyclone 100baseTx at ffffc20000026000.)

ethtool:
# ethtool -i eth2
driver: forcedeth
...
# ethtool -i eth1
driver: forcedeth

Anyway, I think you should talk to the forcedeth maintainer... he probably knows what's going on, or has atleast some ideas what ASUS screwed up...

Re: 2nd NIC is off on Asus M2N-SLI Deluxe (nForce 570 SLI MCP)

Indeed, it is remapped by udev:

Code:

# cat /etc/udev/rules.d/z25_persistent-net.rules

# This file was automatically generated by the /lib/udev/write_net_rules

# program, probably run by the persistent-net-generator.rules rules file.

#

# You can modify it, as long as you keep each rule on a single line.

# MAC addresses must be written in lowercase.



# PCI device 0x10de:0x0373 (forcedeth)

SUBSYSTEM=="net", DRIVERS=="?*", ATTRS{address}=="00:18:f3:67:88:d1", NAME="eth1"



# PCI device 0x10de:0x0373 (forcedeth)

SUBSYSTEM=="net", DRIVERS=="?*", ATTRS{address}=="00:18:f3:67:97:8f", NAME="eth2"



# PCI device 0x10b7:0x9055 (3c59x)

SUBSYSTEM=="net", DRIVERS=="?*", ATTRS{address}=="00:50:04:63:51:3f", NAME="eth0"



# PCI device 0x8086:0x107d (e1000)

SUBSYSTEM=="net", DRIVERS=="?*", ATTRS{address}=="00:15:17:0e:84:df", NAME="eth3"

I added the Intel card as a replacement for the faulty on-board NIC, the problem shows without this card, too. Yet, I can't remember whether I ever tested without the 3com card. Tomorrow I will test again, with both additional network cards removed.

Maintainer: You mean Manfred Spraul? I found his name in forcedeth.c, but he is not listed in MAINTAINERS.

Re: 2nd NIC is off on Asus M2N-SLI Deluxe (nForce 570 SLI MCP)

Do these options have any impact?
"options forcedeth msi=0 msix=0"

Re: 2nd NIC is off on Asus M2N-SLI Deluxe (nForce 570 SLI MCP)

I removed the two other NICs, so that there is no remapping being done anymore. Now the system looks like that:

Code:

# lspci

00:00.0 RAM memory: nVidia Corporation MCP55 Memory Controller (rev a1)

00:01.0 ISA bridge: nVidia Corporation MCP55 LPC Bridge (rev a2)

00:01.1 SMBus: nVidia Corporation MCP55 SMBus (rev a2)

00:01.2 RAM memory: nVidia Corporation MCP55 Memory Controller (rev a2)

00:02.0 USB Controller: nVidia Corporation MCP55 USB Controller (rev a1)

00:02.1 USB Controller: nVidia Corporation MCP55 USB Controller (rev a2)

00:04.0 IDE interface: nVidia Corporation MCP55 IDE (rev a1)

00:05.0 IDE interface: nVidia Corporation MCP55 SATA Controller (rev a2)

00:05.1 IDE interface: nVidia Corporation MCP55 SATA Controller (rev a2)

00:05.2 IDE interface: nVidia Corporation MCP55 SATA Controller (rev a2)

00:06.0 PCI bridge: nVidia Corporation MCP55 PCI bridge (rev a2)

00:08.0 Bridge: nVidia Corporation MCP55 Ethernet (rev a2)

00:09.0 Bridge: nVidia Corporation MCP55 Ethernet (rev a2)

00:0a.0 PCI bridge: nVidia Corporation MCP55 PCI Express bridge (rev a2)

00:0b.0 PCI bridge: nVidia Corporation MCP55 PCI Express bridge (rev a2)

00:0c.0 PCI bridge: nVidia Corporation MCP55 PCI Express bridge (rev a2)

00:0d.0 PCI bridge: nVidia Corporation MCP55 PCI Express bridge (rev a2)

00:0e.0 PCI bridge: nVidia Corporation MCP55 PCI Express bridge (rev a2)

00:0f.0 PCI bridge: nVidia Corporation MCP55 PCI Express bridge (rev a2)

00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration

00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map

00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller

00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control

01:08.0 VGA compatible controller: ATI Technologies Inc 215CT [Mach64 CT] (rev 09)

07:00.0 PCI bridge: Intel Corporation 41210 [Lanai] Serial to Parallel PCI Bridge (A-Segment Bridge) (rev 09)

07:00.2 PCI bridge: Intel Corporation 41210 [Lanai] Serial to Parallel PCI Bridge (B-Segment Bridge) (rev 09)

08:04.0 SCSI storage controller: Triones Technologies, Inc. Unknown device 2340 (rev 09)

09:04.0 SCSI storage controller: Triones Technologies, Inc. Unknown device 2340 (rev 09)

And I put msi=0 msix=0 in /etc/initramfs-tools/modules ...

Code:

# cat /etc/initramfs-tools/modules

# List of modules that you want to include in your initramfs.

#

# Syntax:  module_name [args ...]

#

# You must run update-initramfs(8) to effect this change.



forcedeth msi=0 msix=0

rr2340

... which however did not improve the situation.

I got lucky once after a cold boot (out of approx. ten tries), to have both NICs working. I'm attaching dmesg output of the occasion when both NICs worked and the same for a "normal" occurence, when only the first NIC was working. Both contain full forcedeth debug output, so maybe (hopefully) that will be sufficient to figure out what is going on.

Re: 2nd NIC is off on Asus M2N-SLI Deluxe (nForce 570 SLI MCP)

ahh, a lspci -v , /proc/interrupts, ... would have been nice.

Re: 2nd NIC is off on Asus M2N-SLI Deluxe (nForce 570 SLI MCP)

Quote:

Originally Posted by chunkey

ahh, a lspci -v , /proc/interrupts, ... would have been nice.

I re-added the intel NIC as eth2. Forcedeth is eth0 and eth1.

Code:

# lspci -v

00:00.0 RAM memory: nVidia Corporation MCP55 Memory Controller (rev a1)

        Subsystem: ASUSTeK Computer Inc. Unknown device 8239

        Flags: bus master, 66MHz, fast devsel, latency 0

        Capabilities: [44] HyperTransport: Slave or Primary Interface

        Capabilities: [e0] #00 [fee0]



00:01.0 ISA bridge: nVidia Corporation MCP55 LPC Bridge (rev a2)

        Subsystem: ASUSTeK Computer Inc. Unknown device 8239

        Flags: bus master, 66MHz, fast devsel, latency 0



00:01.1 SMBus: nVidia Corporation MCP55 SMBus (rev a2)

        Subsystem: ASUSTeK Computer Inc. Unknown device 8239

        Flags: 66MHz, fast devsel, IRQ 255

        I/O ports at fc00 [size=64]

        I/O ports at 1c00 [size=64]

        I/O ports at 1c40 [size=64]

        Capabilities: [44] Power Management version 2



00:01.2 RAM memory: nVidia Corporation MCP55 Memory Controller (rev a2)

        Subsystem: ASUSTeK Computer Inc. Unknown device 8239

        Flags: 66MHz, fast devsel



00:02.0 USB Controller: nVidia Corporation MCP55 USB Controller (rev a1) (prog-if 10 [OHCI])

        Subsystem: ASUSTeK Computer Inc. Unknown device 8239

        Flags: bus master, 66MHz, fast devsel, latency 0, IRQ 21

        Memory at fe02f000 (32-bit, non-prefetchable) [size=4K]

        Capabilities: [44] Power Management version 2



00:02.1 USB Controller: nVidia Corporation MCP55 USB Controller (rev a2) (prog-if 20 [EHCI])

        Subsystem: ASUSTeK Computer Inc. Unknown device 8239

        Flags: bus master, 66MHz, fast devsel, latency 0, IRQ 20

        Memory at fe02e000 (32-bit, non-prefetchable) [size=256]

        Capabilities: [44] Debug port

        Capabilities: [80] Power Management version 2



00:04.0 IDE interface: nVidia Corporation MCP55 IDE (rev a1) (prog-if 8a [Master SecP PriP])

        Subsystem: ASUSTeK Computer Inc. Unknown device 8239

        Flags: bus master, 66MHz, fast devsel, latency 0

        [virtual] Memory at 000001f0 (32-bit, non-prefetchable) [disabled] [size=8]

        [virtual] Memory at 000003f0 (type 3, non-prefetchable) [disabled] [size=1]

        [virtual] Memory at 00000170 (32-bit, non-prefetchable) [disabled] [size=8]

        [virtual] Memory at 00000370 (type 3, non-prefetchable) [disabled] [size=1]

        I/O ports at f000 [size=16]

        Capabilities: [44] Power Management version 2



00:05.0 IDE interface: nVidia Corporation MCP55 SATA Controller (rev a2) (prog-if 85 [Master SecO PriO])

        Subsystem: ASUSTeK Computer Inc. Unknown device 8239

        Flags: bus master, 66MHz, fast devsel, latency 0, IRQ 23

        I/O ports at 09f0 [size=8]

        I/O ports at 0bf0 [size=4]

        I/O ports at 0970 [size=8]

        I/O ports at 0b70 [size=4]

        I/O ports at dc00 [size=16]

        Memory at fe02d000 (32-bit, non-prefetchable) [size=4K]

        Capabilities: [44] Power Management version 2

        Capabilities: [b0] Message Signalled Interrupts: Mask- 64bit+ Queue=0/2 Enable-

        Capabilities: [cc] HyperTransport: MSI Mapping



00:05.1 IDE interface: nVidia Corporation MCP55 SATA Controller (rev a2) (prog-if 85 [Master SecO PriO])

        Subsystem: ASUSTeK Computer Inc. Unknown device 8239

        Flags: bus master, 66MHz, fast devsel, latency 0, IRQ 22

        I/O ports at 09e0 [size=8]

        I/O ports at 0be0 [size=4]

        I/O ports at 0960 [size=8]

        I/O ports at 0b60 [size=4]

        I/O ports at c800 [size=16]

        Memory at fe02c000 (32-bit, non-prefetchable) [size=4K]

        Capabilities: [44] Power Management version 2

        Capabilities: [b0] Message Signalled Interrupts: Mask- 64bit+ Queue=0/2 Enable-

        Capabilities: [cc] HyperTransport: MSI Mapping



00:05.2 IDE interface: nVidia Corporation MCP55 SATA Controller (rev a2) (prog-if 85 [Master SecO PriO])

        Subsystem: ASUSTeK Computer Inc. Unknown device 8239

        Flags: bus master, 66MHz, fast devsel, latency 0, IRQ 21

        I/O ports at c400 [size=8]

        I/O ports at c000 [size=4]

        I/O ports at bc00 [size=8]

        I/O ports at b800 [size=4]

        I/O ports at b400 [size=16]

        Memory at fe02b000 (32-bit, non-prefetchable) [size=4K]

        Capabilities: [44] Power Management version 2

        Capabilities: [b0] Message Signalled Interrupts: Mask- 64bit+ Queue=0/2 Enable-

        Capabilities: [cc] HyperTransport: MSI Mapping



00:06.0 PCI bridge: nVidia Corporation MCP55 PCI bridge (rev a2) (prog-if 01 [Subtractive decode])

        Flags: bus master, 66MHz, fast devsel, latency 0

        Bus: primary=00, secondary=01, subordinate=01, sec-latency=32

        Memory behind bridge: fb000000-fcffffff

        Prefetchable memory behind bridge: 40000000-400fffff

        Capabilities: [b8] Subsystem: nVidia Corporation Unknown device cb84

        Capabilities: [8c] HyperTransport: MSI Mapping



00:08.0 Bridge: nVidia Corporation MCP55 Ethernet (rev a2)

        Subsystem: ASUSTeK Computer Inc. Unknown device 8239

        Flags: bus master, 66MHz, fast devsel, latency 0, IRQ 23

        Memory at fe02a000 (32-bit, non-prefetchable) [size=4K]

        I/O ports at b000 [size=8]

        Memory at fe029000 (32-bit, non-prefetchable) [size=256]

        Memory at fe028000 (32-bit, non-prefetchable) [size=16]

        Capabilities: [44] Power Management version 2

        Capabilities: [70] MSI-X: Enable- Mask- TabSize=8

        Capabilities: [50] Message Signalled Interrupts: Mask+ 64bit+ Queue=0/3 Enable-

        Capabilities: [6c] HyperTransport: MSI Mapping



00:09.0 Bridge: nVidia Corporation MCP55 Ethernet (rev a2)

        Subsystem: ASUSTeK Computer Inc. Unknown device 8239

        Flags: bus master, 66MHz, fast devsel, latency 0, IRQ 22

        Memory at fe027000 (32-bit, non-prefetchable) [size=4K]

        I/O ports at ac00 [size=8]

        Memory at fe026000 (32-bit, non-prefetchable) [size=256]

        Memory at fe025000 (32-bit, non-prefetchable) [size=16]

        Capabilities: [44] Power Management version 2

        Capabilities: [70] MSI-X: Enable- Mask- TabSize=8

        Capabilities: [50] Message Signalled Interrupts: Mask+ 64bit+ Queue=0/3 Enable-

        Capabilities: [6c] HyperTransport: MSI Mapping



00:0a.0 PCI bridge: nVidia Corporation MCP55 PCI Express bridge (rev a2) (prog-if 00 [Normal decode])

        Flags: bus master, fast devsel, latency 0

        Bus: primary=00, secondary=02, subordinate=02, sec-latency=0

        Capabilities: [40] Subsystem: nVidia Corporation Unknown device 0000

        Capabilities: [48] Power Management version 2

        Capabilities: [50] Message Signalled Interrupts: Mask- 64bit+ Queue=0/1 Enable+

        Capabilities: [60] HyperTransport: MSI Mapping

        Capabilities: [80] Express Root Port (Slot+) IRQ 0

        Capabilities: [100] Virtual Channel



00:0b.0 PCI bridge: nVidia Corporation MCP55 PCI Express bridge (rev a2) (prog-if 00 [Normal decode])

        Flags: bus master, fast devsel, latency 0

        Bus: primary=00, secondary=03, subordinate=03, sec-latency=0

        Capabilities: [40] Subsystem: nVidia Corporation Unknown device 0000

        Capabilities: [48] Power Management version 2

        Capabilities: [50] Message Signalled Interrupts: Mask- 64bit+ Queue=0/1 Enable+

        Capabilities: [60] HyperTransport: MSI Mapping

        Capabilities: [80] Express Root Port (Slot+) IRQ 0

        Capabilities: [100] Virtual Channel



00:0c.0 PCI bridge: nVidia Corporation MCP55 PCI Express bridge (rev a2) (prog-if 00 [Normal decode])

        Flags: bus master, fast devsel, latency 0

        Bus: primary=00, secondary=04, subordinate=04, sec-latency=0

        Capabilities: [40] Subsystem: nVidia Corporation Unknown device 0000

        Capabilities: [48] Power Management version 2

        Capabilities: [50] Message Signalled Interrupts: Mask- 64bit+ Queue=0/1 Enable+

        Capabilities: [60] HyperTransport: MSI Mapping

        Capabilities: [80] Express Root Port (Slot+) IRQ 0

        Capabilities: [100] Virtual Channel



00:0d.0 PCI bridge: nVidia Corporation MCP55 PCI Express bridge (rev a2) (prog-if 00 [Normal decode])

        Flags: bus master, fast devsel, latency 0

        Bus: primary=00, secondary=05, subordinate=05, sec-latency=0

        I/O behind bridge: 00009000-00009fff

        Memory behind bridge: fde00000-fdefffff

        Capabilities: [40] Subsystem: nVidia Corporation Unknown device 0000

        Capabilities: [48] Power Management version 2

        Capabilities: [50] Message Signalled Interrupts: Mask- 64bit+ Queue=0/1 Enable+

        Capabilities: [60] HyperTransport: MSI Mapping

        Capabilities: [80] Express Root Port (Slot+) IRQ 0

        Capabilities: [100] Virtual Channel



00:0e.0 PCI bridge: nVidia Corporation MCP55 PCI Express bridge (rev a2) (prog-if 00 [Normal decode])

        Flags: bus master, fast devsel, latency 0

        Bus: primary=00, secondary=06, subordinate=06, sec-latency=0

        I/O behind bridge: 00007000-00008fff

        Memory behind bridge: fdd00000-fddfffff

        Capabilities: [40] Subsystem: nVidia Corporation Unknown device 0000

        Capabilities: [48] Power Management version 2

        Capabilities: [50] Message Signalled Interrupts: Mask- 64bit+ Queue=0/1 Enable+

        Capabilities: [60] HyperTransport: MSI Mapping

        Capabilities: [80] Express Root Port (Slot+) IRQ 0

        Capabilities: [100] Virtual Channel



00:0f.0 PCI bridge: nVidia Corporation MCP55 PCI Express bridge (rev a2) (prog-if 00 [Normal decode])

        Flags: bus master, fast devsel, latency 0

        Bus: primary=00, secondary=07, subordinate=09, sec-latency=0

        I/O behind bridge: 00005000-00006fff

        Memory behind bridge: fd900000-fdcfffff

        Capabilities: [40] Subsystem: nVidia Corporation Unknown device 0000

        Capabilities: [48] Power Management version 2

        Capabilities: [50] Message Signalled Interrupts: Mask- 64bit+ Queue=0/1 Enable+

        Capabilities: [60] HyperTransport: MSI Mapping

        Capabilities: [80] Express Root Port (Slot+) IRQ 0

        Capabilities: [100] Virtual Channel



00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration

        Flags: fast devsel

        Capabilities: [80] HyperTransport: Host or Secondary Interface



00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map

        Flags: fast devsel



00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller

        Flags: fast devsel



00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control

        Flags: fast devsel

        Capabilities: [f0] #0f [0010]



01:08.0 VGA compatible controller: ATI Technologies Inc 215CT [Mach64 CT] (rev 09) (prog-if 00 [VGA])

        Flags: VGA palette snoop, stepping, medium devsel

        Memory at fb000000 (32-bit, non-prefetchable) [size=16M]

        Expansion ROM at 40000000 [disabled] [size=64K]



05:00.0 Ethernet controller: Intel Corporation 82572EI Gigabit Ethernet Controller (rev 06)

        Subsystem: Intel Corporation PRO/1000 PT Server Adapter

        Flags: bus master, fast devsel, latency 0, IRQ 1273

        Memory at fdee0000 (32-bit, non-prefetchable) [size=128K]

        Memory at fdec0000 (32-bit, non-prefetchable) [size=128K]

        I/O ports at 9c00 [size=32]

        Expansion ROM at fdea0000 [disabled] [size=128K]

        Capabilities: [c8] Power Management version 2

        Capabilities: [d0] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable+

        Capabilities: [e0] Express Endpoint IRQ 0

        Capabilities: [100] Advanced Error Reporting

        Capabilities: [140] Device Serial Number df-84-0e-ff-ff-17-15-00



07:00.0 PCI bridge: Intel Corporation 41210 [Lanai] Serial to Parallel PCI Bridge (A-Segment Bridge) (rev 09) (prog-if 00 [Normal decode])

        Flags: bus master, fast devsel, latency 0

        Bus: primary=07, secondary=08, subordinate=08, sec-latency=32

        I/O behind bridge: 00006000-00006fff

        Memory behind bridge: fdb00000-fdcfffff

        Capabilities: [44] Express PCI/PCI-X Bridge IRQ 0

        Capabilities: [5c] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable-

        Capabilities: [6c] Power Management version 2

        Capabilities: [d8] PCI-X bridge device

        Capabilities: [100] Advanced Error Reporting

        Capabilities: [300] Power Budgeting



07:00.2 PCI bridge: Intel Corporation 41210 [Lanai] Serial to Parallel PCI Bridge (B-Segment Bridge) (rev 09) (prog-if 00 [Normal decode])

        Flags: bus master, fast devsel, latency 0

        Bus: primary=07, secondary=09, subordinate=09, sec-latency=32

        I/O behind bridge: 00005000-00005fff

        Memory behind bridge: fd900000-fdafffff

        Capabilities: [44] Express PCI/PCI-X Bridge IRQ 0

        Capabilities: [5c] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable-

        Capabilities: [6c] Power Management version 2

        Capabilities: [d8] PCI-X bridge device

        Capabilities: [100] Advanced Error Reporting

        Capabilities: [300] Power Budgeting



08:04.0 SCSI storage controller: Triones Technologies, Inc. Unknown device 2340 (rev 09)

        Subsystem: Marvell Technology Group Ltd. Unknown device 11ab

        Flags: bus master, 66MHz, medium devsel, latency 32, IRQ 16

        Memory at fdb00000 (64-bit, non-prefetchable) [size=1M]

        I/O ports at 6c00 [size=256]

        Capabilities: [40] Power Management version 2

        Capabilities: [50] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable-

        Capabilities: [60] PCI-X non-bridge device



09:04.0 SCSI storage controller: Triones Technologies, Inc. Unknown device 2340 (rev 09)

        Subsystem: Marvell Technology Group Ltd. Unknown device 11ab

        Flags: bus master, 66MHz, medium devsel, latency 32, IRQ 16

        Memory at fd900000 (64-bit, non-prefetchable) [size=1M]

        I/O ports at 5c00 [size=256]

        Capabilities: [40] Power Management version 2

        Capabilities: [50] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable-

        Capabilities: [60] PCI-X non-bridge device

Re: 2nd NIC is off on Asus M2N-SLI Deluxe (nForce 570 SLI MCP)

Code:

# cat /proc/interrupts

           CPU0       CPU1

  0:     238277          0   IO-APIC-edge      timer

  1:       1655          0   IO-APIC-edge      i8042

  6:          3          0   IO-APIC-edge      floppy

  7:          0          0   IO-APIC-edge      parport0

  8:          1          0   IO-APIC-edge      rtc

  9:          0          0   IO-APIC-fasteoi   acpi

 12:          4          0   IO-APIC-edge      i8042

 16:       1329          0   IO-APIC-fasteoi   rr2340, rr2340

 20:          0          0   IO-APIC-fasteoi   ehci_hcd:usb2

 21:       4577          0   IO-APIC-fasteoi   ohci_hcd:usb1, libata

 22:       4935          0   IO-APIC-fasteoi   libata

 23:     100978          0   IO-APIC-fasteoi   libata, eth0

1273:       2593          0   PCI-MSI-edge      eth2

NMI:          0          0

LOC:     238240     237717

ERR:          0

Anything else you'd be interested in?

Re: 2nd NIC is off on Asus M2N-SLI Deluxe (nForce 570 SLI MCP)

You stated that you "put msi=0 msix=0 in /etc/initramfs-tools/modules". Is that traditionally where your Linux distribution keeps its kernel module options, rather than modprobe.conf? Did you rebuild the initrd & reboot after making that change?

If you boot with hpet=disable does that have any impact?

Re: 2nd NIC is off on Asus M2N-SLI Deluxe (nForce 570 SLI MCP)

Quote:

Originally Posted by netllama

You stated that you "put msi=0 msix=0 in /etc/initramfs-tools/modules". Is that traditionally where your Linux distribution keeps its kernel module options, rather than modprobe.conf?

I was not sure whether modprobe.conf would be honoured by modules loaded from initrd, that's why I put it in /etc/initramfs-tools/modules. (I'm using Debian Etch (amd64) by the way.) Of course I also tried to modprobe forcedeth msi=0 msix=0 on the command line, but it was all to no avail.

Quote:

Originally Posted by netllama

Did you rebuild the initrd & reboot after making that change?

Yes.

Quote:

Originally Posted by netllama

If you boot with hpet=disable does that have any impact?

No, I don't see any change.

Re: 2nd NIC is off on Asus M2N-SLI Deluxe (nForce 570 SLI MCP)

I originally posted a detailed replay, but much to my dismay, these forums appear to wipe your post if you aren't logged in when you hit quick reply so I lost it ;( Between that and the captcha on the registration page being quite possibly the worst I have ever seen...doh. But I digress, I'll give you the brief version of my now lost post.

I just built 4 machines using this mobo on 32 bit etch 2.6.21 smp (64x2 6000+). 2 machines are fine, both interfaces work as expected. On the other 2 machines, port 1 is fine and port 2 is bad. One of them is identical to the problems experienced by Extensive2, including the workaround. On the other, the 2nd nic comes up, but errors on about 5 of every 6 frames it processes. I get a throughput of around 2-4k/s on it. Using either of the good machines over the same infrastructrue works as expected. I haven't tried the msi=0, msix=0 parameters yet, I will do that now and post my experience.

Re: 2nd NIC is off on Asus M2N-SLI Deluxe (nForce 570 SLI MCP)

Thanks for taking the time to repost!

Quote:

Originally Posted by Outtascope

I just built 4 machines using this mobo on 32 bit etch 2.6.21 smp (64x2 6000+). 2 machines are fine, both interfaces work as expected. On the other 2 machines, port 1 is fine and port 2 is bad. One of them is identical to the problems experienced by Extensive2, including the workaround. On the other, the 2nd nic comes up, but errors on about 5 of every 6 frames it processes. I get a throughput of around 2-4k/s on it. Using either of the good machines over the same infrastructrue works as expected.

To me that seems to indicate a production error at Asus. Maybe we should just return the erroneous boards. What's your opinion?