View Single Post
Old 11-19-06, 11:36 AM   #13
Darkvater
Registered User
 
Join Date: Feb 2005
Posts: 57
Default Re: [beta driver] DVI EDID problem

I am having the same problem as many here.

Code:
(II) NVIDIA(0): Option "UseDisplayDevice" "DFP" converted to "DFP-0".
(II) NVIDIA(0): Frequency information for Samsung SyncMaster (DFP-0):
(II) NVIDIA(0):   HorizSync   : 30.000-81.000 kHz
(II) NVIDIA(0):   VertRefresh : 56.000-75.000 Hz
(II) NVIDIA(0):     (HorizSync from EDID)
(II) NVIDIA(0):     (VertRefresh from EDID)
(II) NVIDIA(0):
(II) NVIDIA(0): --- Building ModePool for Samsung SyncMaster (DFP-0) ---
(II) NVIDIA(0):   Validating Mode "1680x1050":
(II) NVIDIA(0):     1680 x 1050 @ 60 Hz
(II) NVIDIA(0):     For use as DFP backend.
(II) NVIDIA(0):     Mode Source: EDID
(II) NVIDIA(0):       Pixel Clock      : 146.25 MHz
(II) NVIDIA(0):       HRes, HSyncStart : 1680, 1784
(II) NVIDIA(0):       HSyncEnd, HTotal : 1960, 2240
(II) NVIDIA(0):       VRes, VSyncStart : 1050, 1053
(II) NVIDIA(0):       VSyncEnd, VTotal : 1059, 1089
(II) NVIDIA(0):       H/V Polarity     : -/+
(WW) NVIDIA(0):     Mode is rejected: PixelClock (146.2 MHz) too high for
(WW) NVIDIA(0):     Display Device (Max: 140.4 MHz).
Code:
(II) NVIDIA(0): NVIDIA GPU GeForce FX 5600 at PCI:1:0:0 (GPU-0)
(--) NVIDIA(0): Memory: 262144 kBytes
(II) NVIDIA(0): GPU Architecture: 0x30
(II) NVIDIA(0): GPU Implementation: 0x31
(II) NVIDIA(0): GPU Revision: 0xa1
(--) NVIDIA(0): VideoBIOS: 04.31.20.40.00
(--) NVIDIA(0): Found 2 CRTCs on board
(II) NVIDIA(0): Supported display device(s): CRT-0, CRT-1, DFP-0, TV-0
(II) NVIDIA(0): Bus detected as AGP
(II) NVIDIA(0): Detected AGP rate: 2X
(--) NVIDIA(0): Interlaced video modes are supported on this GPU

(--) NVIDIA(0): Connected display device(s) on GeForce FX 5600 at PCI:1:0:0:
(--) NVIDIA(0):     Samsung SyncMaster (DFP-0)
(--) NVIDIA(0): Samsung SyncMaster (DFP-0): 140.4 MHz maximum pixel clock
(--) NVIDIA(0): Samsung SyncMaster (DFP-0): Internal Single Link TMDS
(--) NVIDIA(0): Samsung SyncMaster (DFP-0): Native FlatPanel Scaling is
(--) NVIDIA(0):     supported
(--) NVIDIA(0): Samsung SyncMaster (DFP-0): DFP modes are limited to 60 Hz
(--) NVIDIA(0):     refresh rate
(--) NVIDIA(0):
(--) NVIDIA(0): --- EDID for Samsung SyncMaster (DFP-0) ---
(--) NVIDIA(0): EDID Version                 : 1.3
(--) NVIDIA(0): Manufacturer                 : SAM
(--) NVIDIA(0): Monitor Name                 : Samsung SyncMaster
(--) NVIDIA(0): Product ID                   : 542
(--) NVIDIA(0): 32-bit Serial Number         : 1212232240
(--) NVIDIA(0): Serial Number String         : HSHLA00788
(--) NVIDIA(0): Manufacture Date             : 2006, week 40
(--) NVIDIA(0): DPMS Capabilities            : Active Off
(--) NVIDIA(0): Prefer first detailed timing : Yes
(--) NVIDIA(0): Supports GTF                 : No
(--) NVIDIA(0): Maximum Image Size           : 430mm x 270mm
(--) NVIDIA(0): Valid HSync Range            : 30 kHz - 81 kHz
(--) NVIDIA(0): Valid VRefresh Range         : 56 Hz - 75 Hz
(--) NVIDIA(0): EDID maximum pixel clock     : 160.0 MHz
On my brandnew Samsung 205bw with 1680x1050 resolution on an (Asus) NVidia FX5600 card. Does this mean I need a new videocard or something? I cannot get it to work in widescreen mode at all . Nothing higher than 1280x1024 works.

Some people talked about an Option "ModeValidation" "NoEdidDFPMaxSizeCheck", but the logfiles says it doesn't recognize this mode?

I have the logfile here: http://darkvater.openttd.org/Xorg.0.log

Last edited by Darkvater; 11-19-06 at 12:01 PM.
Darkvater is offline   Reply With Quote