View Single Post
Old 05-16-03, 11:36 AM   #1
schotty
Registered User
 
Join Date: May 2003
Location: Milwaukee
Posts: 8
Send a message via ICQ to schotty Send a message via AIM to schotty Send a message via Yahoo to schotty
Default Difficulites in making my Geforce 2 GTS display a cloned screen

Hello I am using RH9 and drivers 4349. I have the desire to clone my output to my television screen. I currently have the following issue :

When I laod up X, I get the following error message :

Code:
(WW) NVIDIA(0): 2 display devices connected, but only 1 supported;
(WW) NVIDIA(0):      adjusting...
And here is my X config. I can run X on my CRT just fine. But no output (after the initial flicker) gets sent out to the television. :

Code:
Section "ServerLayout"
	Identifier	"Default Layout"
	Screen		0 "Screen0" 0 0
	InputDevice	"Mouse0" "CorePointer"
	InputDevice	"Keyboard0" "CoreKeyboard"
EndSection

Section "Files"
	RgbPath      "/usr/X11R6/lib/X11/rgb"
	FontPath     "unix/:7100"
EndSection

Section "Module"
	Load  "dbe"
	Load  "extmod"
	Load  "fbdevhw"
	Load  "glx"
	Load  "record"
	Load  "freetype"
	Load  "type1"
EndSection

Section "InputDevice"
	Identifier  "Keyboard0"
	Driver      "keyboard"
	Option	    "XkbRules" "xfree86"
	Option	    "XkbModel" "pc105"
	Option	    "XkbLayout" "us"
EndSection

Section "InputDevice"
	Identifier  "Mouse0"
	Driver      "mouse"
	Option	    "Protocol" "IMPS/2"
	Option	    "Device" "/dev/input/mice"
	Option	    "ZAxisMapping" "4 5"
	Option	    "Emulate3Buttons" "no"
EndSection

Section "Monitor"
	Identifier   "Monitor0"
	VendorName   "Monitor Vendor"
	ModelName    "IBM P70"
	HorizSync    29.0 - 82.0
	VertRefresh  50.0 - 120.0
	Option	    "dpms"
EndSection

Section "Device"
	Identifier	"Videocard0"
	Driver		"nvidia"
	VendorName	"Videocard vendor"
	BoardName	"NVIDIA GeForce 2 GTS (generic)"
	BusID		"PCI:1:0:0"
	Screen		0
	

	##################################################
	# Advice from alien999999999 to clone the screen #
	##################################################

	Option "TwinView" "on"
	Option "TwinViewOrientation" "Clone"
	Option "TVStandard" "NTSC-M" 
	Option "SecondMonitorHorizSync" "30-50"
	Option "SecondMonitorVertRefresh" "60"
	Option "ConnectedMonitor" "CRT, TV"
	Option "TVOutFormat" "SVIDEO"
	Option "MetaModes" "1280x1024, 800x600"
EndSection

Section "Screen"
	Identifier "Screen0"
	Device     "Videocard0"
	Monitor    "Monitor0"
	DefaultDepth     16
	SubSection "Display"
		Depth     24
		Modes    "1280x1024" "1280x960" "1152x864" "1024x768" "800x600" "640x480"
	EndSubSection
	SubSection "Display"
		Depth     16
		Modes    "1280x1024" "1280x960" "1152x864" "1024x768" "800x600" "640x480"
	EndSubSection
	SubSection "Display"
		Depth     15
		Modes    "1280x1024" "1280x960" "1152x864" "1024x768" "800x600" "640x480"
	EndSubSection
	SubSection "Display"
		Depth     8
		Modes    "1280x1024" "1280x960" "1152x864" "1024x768" "800x600" "640x480"
	EndSubSection
	SubSection "Display"
		Depth     4
		Modes    "1280x1024" "1280x960" "1152x864" "1024x768" "800x600" "640x480"
	EndSubSection
EndSection
Any ideas? According to alien, I should be able to clone. However the X log says otherwise. I *DO* plan on upgrading my driver to the latest soon, but just havent had the time. IIf that has ALOT to do with it, I can upgrade then report back.

Thanks much!
Andrew
schotty is offline   Reply With Quote