View Single Post
Old 10-07-02, 10:30 AM   #25
Rocketeer
Guest
 
Posts: n/a
Default

And here are the essential parts of the XF86Config:

Code:
Section "Module"
# This loads the DBE extension module.
# This loads the miscellaneous extensions module, and disables
# initialisation of the XFree86-DGA extension within that module.
# This loads the Type1 and FreeType font modules
    Load       "glx"
	Load  "dbe"  	# Double buffer extension
	SubSection "extmod"
		Option	    "omit xfree86-dga"   # don't initialise the DGA extension
	EndSubSection
	Load  "type1"
	Load  "freetype"# This loads the GLX module
EndSection

Section "Monitor"
# HorizSync is in kHz unless units are specified.
# HorizSync may be a comma separated list of discrete values, or a
# comma separated list of ranges of values.
# NOTE: THE VALUES HERE ARE EXAMPLES ONLY.  REFER TO YOUR MONITOR'S
# USER MANUAL FOR THE CORRECT NUMBERS.
#    HorizSync	30-64         # multisync
#    HorizSync	31.5, 35.2    # multiple fixed sync frequencies
#    HorizSync	15-25, 30-50  # multiple ranges of sync frequencies
# VertRefresh is in Hz unless units are specified.
# VertRefresh may be a comma separated list of discrete values, or a
# comma separated list of ranges of values.
# NOTE: THE VALUES HERE ARE EXAMPLES ONLY.  REFER TO YOUR MONITOR'S
# USER MANUAL FOR THE CORRECT NUMBERS.
	Identifier   "gericom"
	ModelName    "Unknown monitor"
	HorizSync    30.0 - 98.0
	VertRefresh  50.0 - 160.0
EndSection
Section "Device"
# The chipset line is optional in most cases.  It can be used to override
# the driver's chipset detection, and should not normally be specified.
#    Chipset	"generic"
# The Driver line must be present.  When using run-time loadable driver
# modules, this line instructs the server to load the specified driver
# module.  Even when not using loadable driver modules, this line
# indicates which driver should interpret the information in this section.
# The BusID line is used to specify which of possibly multiple devices
# this section is intended for.  When this line isn't present, a device
# section can only match up with the primary video device.  For PCI
# devices a line like the following could be used.  This line should not
# normally be included unless there is more than one video device
# intalled.
#    BusID      "PCI:0:10:0"
#    VideoRam	256
#    Clocks	25.2 28.3
	Identifier  "Standard VGA"
	Driver      "vga"
	VendorName  "Unknown"
	BoardName   "Unknown"
EndSection

Section "Device"
    #VideoRam    32768
    # Insert Clocks lines here if appropriate
	Identifier  "geforceself"
	Driver      "nvidia"
        Option      "NvAgp" "1"
	BoardName   "NVIDIA GeForce 2 MX self"
	VideoRam    32768
EndSection

Section "Screen"
	Identifier "Screen 1"
	Device     "geforceself"
	Monitor    "gericom"
	DefaultDepth     16
	SubSection "Display"
		Depth     8
		Modes    "640x480" "800x600" "1024x768" "1280x1024"
	EndSubSection
	SubSection "Display"
		Depth     16
		Modes    "1024x768" "800x600" "640x480"
	EndSubSection
	SubSection "Display"
		Depth     24
		Modes    "640x480" "800x600" "1024x768" "1280x1024"
	EndSubSection
EndSection
So, any hints for me?

Thank you very much
  Reply With Quote