Go Back   nV News Forums > Hardware Forums > Rumor Mill

Newegg Daily Deals

Thread Tools
Old 06-04-12, 07:47 AM   #1
Registered User
josiahsuarez's Avatar
Join Date: Feb 2008
Location: Dallas, Texas
Posts: 739
Smile CMOS scaling... beyond 10nm!

this is a bit of good news, I think

CMOS technology scaling will go on for the foreseeable future but, as we enter the 10nm node, process complexity reduction and variability control will become crucial and drive technology decisions, said An Steegen, senior vice president process technology at Imec, at the annual IMEC Technology Forum last week at the Square meeting center in Brussels, Belgium.

Tomorrow’s smart systems will require more computing power and storage capacity, exceeding what today’s processors and memories can deliver. This drives the need for technology scaling.

In her keynote, Steegen explained how Imec is helping to enable chip scaling beyond 10 nm. Moore’s Law through 19 nm can be lithography-enabled but, after that, it is necessary to look at materials and new design architectures.

Steegen’s message was that CMOS scaling is still possible. It’s just harder. Driving to sub-15nm dimensions requires EUV lithography and advanced patterning. It also implies a migration towards 3D device architectures such as FinFET and calls for material innovation with high-mobility channel materials.

Moore’s law continues but, Steegen specified, it increases complexity, cost and variability. New technology and design solutions together with co-optimization are required.

“The good news is that CMOS still scales, from planar Si device architectures (20 nm) to FinFET device architectures (14 nm) to better control short channel effects. But when you scale, when you introduce new materials, variability increases,” she stated.

In a post-conference discussion with EE Times, Steegen provided more details on the variability issue as we move beyond 10 nm.

“Moving to fully-depleted channel devices like FinFET, allowing us to minimize doping in the channel, we have alleviated some of the variability issues associated with random dopants,” Steegen explained. “This is reflected in the reduced device mismatch. However, with non-planar devices, new variability emerges. With sidewall conduction and increase surface-to-volume ratio, trap and defect induced variation (eg. Low-Freq Noise, BTI reliability, etc.) become more important.

She continued: “Some of these new factors carry into 10nm technology. Beyond this, we expect new variability influences due to new material in the channel and advanced gate-stack modules introduced to boost device performance. New random defects may arise from the challenging integration (eg. Selective epitaxial growth of the heterostructure). Moreover, this material alters the interaction between the channel carriers and the traps/defects giving rise to changes in reliability, and noise.”

When asked what needs to be done to ease the variability issue, Steegen explained that Imec is looking into engineering the material to improve on quality.

There is also fundamental study on how to engineer the energy bands of the channel material to optimize reliability and performance. For instance, she noted, “we have looked into the engineering of implant-free quantum well SiGe channel devices to improved NBTI reliability. Work is ongoing to study the approach for FinFET devices for beyond 14nm applications.”

Steegen explained that, as part of the program, Imec is working to identify paradigm shifts in design. The research institute explores potential solutions, some of which require support by EDA tools. For that purpose, Imec collaborates with EDA vendors in such diverse domains as 3D Design-For-Test, TCAD, impact of litho options on P&R, OPC, 3D system design exploration, etc.

Her last words at the conference were encouraging. “Variability and cost must be considered as from the beginning. We have been reinventing ourselves many many times in the semiconductor industry. We will do it again and again,” she concluded.
josiahsuarez is offline   Reply With Quote
Old 06-04-12, 01:15 PM   #2
Registered User
Join Date: Aug 2002
Location: San Jose, CA
Posts: 449
Default Re: CMOS scaling... beyond 10nm!

You have a lot of companies investing a lot of dollars to continue Moore's law.
They may have workable and know road maps till 10nm, but they have plans up to 6nm at least.

Those maps are drawn over 10 years earlier, to identify what is needed to make it happen and dedicate the correct resources at the right time.

By now, all manufacturers are basically working together on those. They used to have 2 consortium (one centered on Intel and the other with pretty much everyone else, like IBM/TSMC/Samsung), but they are basically merging into one as the cost of researching those technologies become more ludicrous and the volume needed for break-even is unattainable by a single company.
As the universe is curved, there cannot be a straight answer...
frenchy2k1 is offline   Reply With Quote
Old 06-14-12, 03:59 PM   #3
XDanger's Avatar
Join Date: Nov 2005
Posts: 5,729
Default Re: CMOS scaling... beyond 10nm!

what's that material that isn't graphene but the same structure?

edit: silicene
2500K 4.7ghz,P8P67Pro,120gb Force3, 8gb Vengeance,GTX970,TX850v2,W7HP,LaCie Blue 22" crt COMMODORE 64 Silver Label 1Mhz/128D 4Mhz(Z80)

Last edited by XDanger; 06-20-12 at 05:32 PM.
XDanger is offline   Reply With Quote

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Problem connecting Pioneer VSX-S300 to Nvidia Ion - flat panel scaling solves it? wild_oscar NVIDIA Linux 3 06-17-12 07:18 AM

All times are GMT -5. The time now is 09:10 PM.

Powered by vBulletin® Version 3.7.1
Copyright ©2000 - 2015, Jelsoft Enterprises Ltd.
Copyright ©1998 - 2014, nV News.