Go Back   nV News Forums > Linux Support Forums > NVIDIA Linux

Newegg Daily Deals

Reply
 
Thread Tools
Old 10-19-07, 02:20 PM   #1
enito
Registered User
 
Join Date: Aug 2004
Posts: 23
Default 6600 GT AGP and TEMP

Hi,

i have a doubt, with original fan , my gpu in idle time have 61 C

now i changed the fan stuff with this,

http://www.vantecusa.com/p_ccba5c.html

its look a really good solution but now i get this :

nvclock -i
-- General info --
Card: nVidia Geforce 6600/GT
Architecture: NV43 A4
PCI id: 0xf1
GPU clock: 299.250 MHz
Bustype: AGP (BR02)

-- Pipeline info --
Pixel units: 2x4 (11b)
Vertex units: 3x1 (111b)
HW masked units: None
SW masked units: None

-- Memory info --
Amount: 128 MB
Type: 128 bit DDR3
Clock: 1002.375 MHz

-- Sensor info --
Sensor: GPU Internal Sensor
GPU temperature: 69C
Fanspeed: 100.0%

-- VideoBios information --
Version: 05.43.02.57.00
Signon message: NV43 p218 sku1 VGA BIOS
Performance level 0: gpu 300MHz/memory 1000MHz/1.30V/100%
Performance level 1: gpu 500MHz/memory 1000MHz/1.40V/100%
VID mask: 3
Voltage level 0: 1.30V, VID: 0
Voltage level 1: 1.40V, VID: 3


i get more temp? with a better fan system?

what can be?

any clue, welcome and thx for your time!
enito is offline   Reply With Quote
Old 10-20-07, 02:28 AM   #2
pe1chl
Registered User
 
Join Date: Aug 2003
Posts: 1,026
Default Re: 6600 GT AGP and TEMP

Before I had 72 deg C on my 6600GT card with the standard fan.
I removed the fan and heatsink and re-fitted it, and it dropped to 63 deg. With the same components.
Probably the wacky mounting of the heatsink (it is just pulled to the circuit board using two plastic pins) results in poor conducting of the heat from chip to heatsink. No matter how much fan you mount on that, the chip will still run hot as a result.
pe1chl is offline   Reply With Quote
Old 10-20-07, 11:08 AM   #3
_john_i_
gtx260/8200M G/DIY Linux
 
Join Date: Aug 2004
Location: Austin, TX USA
Posts: 137
Default Re: 6600 GT AGP and TEMP

Same here. I used to have lots of lockups, and finally traced it to the heat
of my 6600GT. Once I replaced the factory fan with a big replacement heat/sink fan combo my stability problems went away.

The factory heatsink/fan combo on a lot of the 6600gt's were terribly underpowered for the amount of heat they generate.
_john_i_ is offline   Reply With Quote
Old 10-20-07, 01:10 PM   #4
logan
Registered User
 
Join Date: Aug 2002
Posts: 492
Default Re: 6600 GT AGP and TEMP

I recently installed a Zalman FS-V7 on my XFX 6600 GT AGP. The ramsinks made it very difficult to seat the cooler, even after more than one adjustment. I still don't think it's properly seated, but my idle temps went from 61c to 50c and I haven't seen anything above 56c under load.

If you're seeing higher temps with the new cooler, maybe it's not properly seated and/or there's not enough thermal paste. The instructions with the Zalman cooler also mentioned cleaning the processor with 90% rubbing alcohol or such, before applying new thermal paste.
logan is offline   Reply With Quote
Old 10-20-07, 04:57 PM   #5
Thunderbird
 
Join Date: Jul 2002
Location: Netherlands, Europe
Posts: 2,105
Default Re: 6600 GT AGP and TEMP

His problem is just that his new fan increases the gpu temperature. This is likely due to bad contact (you need enough but not too much thermal paste) and you also need a good inlet for cold air and some way to remove hot air. If the airflow inside the case isn't right a big cooler won't help.
Thunderbird is offline   Reply With Quote
Reply


Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump


All times are GMT -5. The time now is 12:02 PM.


Powered by vBulletin® Version 3.7.1
Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.
Copyright 1998 - 2014, nV News.