|05-21-03, 02:15 PM||#1|
Join Date: May 2003
startx problem "screen found, but none have usable configuration."
When I startx, it gives me an error that says "screen found, but none have usable configuration."
When I "lsmod", i can see that the "NVdriver" is loaded (but nothing is "using" it)...so i'm assuming that its not a kernel source problem.....or is it?
XFree86 Version 18.104.22.168 / X Window System
(protocol Version 11, revision 0, vendor release 6510)
Release Date: 21 December 2001
If the server is older than 6-12 months, or if your card is
newer than the above date, look for a newer version before
reporting problems. (See <http://www.XFree86.Org/FAQ>)
Build Operating System: Linux 2.4.17 i686 [ELF]
Module Loader present
(==) Log file: "/var/log/XFree86.0.log", Time: Wed May 21 12:31:54 2003
(==) Using config file: "/etc/X11/XF86Config-4"
(II) Setting vga for screen 0.
(II) Loading sub module "vgahw"
(II) LoadModule: "vgahw"
(II) Loading /usr/X11R6/lib/modules/libvgahw.a
(II) Module vgahw: vendor="The XFree86 Project"
compiled for 22.214.171.124, module version = 0.1.0
ABI class: XFree86 Video Driver, version 0.4
(**) NVIDIA(0): Depth 24, (--) framebuffer bpp 32
(==) NVIDIA(0): RGB weight 888
(==) NVIDIA(0): Default visual is TrueColor
(==) NVIDIA(0): Using gamma correction (1.0, 1.0, 1.0)
(--) NVIDIA(0): Linear framebuffer at 0xE0000000
(--) NVIDIA(0): MMIO registers at 0xEC000000
(WW) System lacks support for changing MTRRs
(EE) NVIDIA(0): Failed to initialize the NVIDIA kernel module!
(EE) NVIDIA(0): *** Aborting ***
(II) UnloadModule: "nvidia"
(II) UnloadModule: "vgahw"
(II) Unloading /usr/X11R6/lib/modules/libvgahw.a
(EE) Screen(s) found, but none have a usable configuration.
Fatal server error:
no screens found
Using Debian 3.0, kernel 2.4.20 Don't know why it says 2.4.17 in the log file; Could I be loading the driver in the wrong kernel? I did compile a new one a few days ago, but that was from 2.2.16 (I think).
Using the nForce mother board which has the vidcard intergrated.
Using this driver: http://www.nvidia.com/view.asp?IO=l...y_ia32_1.0-4363 <http://www.nvidia.com/view.asp?IO=li..._ia32_1.0-4363>
Hope thats enough information.
I'll take ANY suggestions!
|05-21-03, 05:00 PM||#2|
Join Date: Sep 2002
If NVdriver is loaded, then your driver update didn't finish successfully. The kernel module is no longer named NVdriver in drivers 4191, 4349, or 4363; it's now named just "nvidia"(.o, but the .o should be ignored in modprobe or insmod commands) instead.
Try to modprobe nvidia (as root, obviously) -- if you get a module not found error, then rerun the installer, and make sure you check the nvidia-installer.log when you're done. The installer should delete the old NVdriver kernel module for you, so it almost sounds like it didn't even start up correctly.
It says 2.4.17 in the log file because that's the build operating system, not the version it's running under. It just means that whoever (at Debian) built the XFree86 package, was using kernel 2.4.17 at the time -- it shouldn't matter.
Registered Linux User #219692
|05-21-03, 06:22 PM||#3|
Join Date: May 2003
ok, now I'm getting somewhere....
When I insmod or modprobe, it says this: nvidia.o:init_modulesevice or resource busy. Incorrect module paramters, irq or i/o
I tried inserting the irq of my vid card when i insmod, but it says "invalid parameters".
Does anyone know how I can fix this?