10-12-05, 06:54 PM
|
#1 |
|
|
Registered User
Join Date: Oct 2005
Location: San Diego, CA
Posts: 12
|
Cannot get 1920x1200 on D800 (wrong virtual size)
Hi, I followed the instructions in http://www.nvnews.net/vbulletin/showthread.php?t=52257 to install the new nvidia driver. However, I can't seem to get to the native 1920x1200 (wuxga) resolution of my Dell D800 laptop. I keep getting the message:
(II) NVIDIA(0): Not using mode "1920x1200" (width too large for virtual size) and (II) NVIDIA(0): Virtual screen size determined to be 1280 x 1024 no matter what I do! I have already tried setting "Virtual 1920 1200" in subscetion "display", but to no effect. Any suggestions? Thanks, Alan |
|
|
|
|
10-12-05, 07:07 PM
|
#2 |
|
Registered User
Join Date: Oct 2005
Location: San Diego, CA
Posts: 12
|
Re: Cannot get 1920x1200 on D800 (wrong virtual size)
More info:
/etc/X11/xorg.conf: http://pastebin.com/391727 /var/log/Xorg.0.log: http://pastebin.com/391729 Card: GeForce4 Ti 4200 Go AGP 8x Dell D800, 1920x1200 wuxga lcd monitor nVidia driver version 1.0-7667 on Solaris 10 (maximally patched as of 2005-10-11) Alan Thompson  |
|
|
|
|
|
|
10-13-05, 07:50 PM
|
#3 |
|
Registered User
Join Date: Oct 2005
Location: San Diego, CA
Posts: 12
|
Re: Cannot get 1920x1200 on D800 (wrong virtual size)
More info: Here is the /var/log/Xorg.0.log:
OK, it no longer complains about the wrong virtual size. It even says: (**) NVIDIA(0): Validated modes for display device DFP-0: (**) NVIDIA(0): Mode "1920x1200": 162.0 MHz, 65.3 kHz, 52.3 Hz (**) NVIDIA(0): Default mode "1400x1050": 155.8 MHz, 81.5 kHz, 74.8 Hz (**) NVIDIA(0): Default mode "1600x1200": 162.0 MHz, 75.0 kHz, 60.0 Hz etc.... Notice how it says (II) NVIDIA(0): Setting mode "1920x1200" and then later (II) NVIDIA(0): Setting mode "1280x1024" Very curious! Anybody got any clues? Alan Thompson Code:
X Window System Version 6.8.2 (Sun Xorg Release 1.1 for Solaris 10) Release Date: 9 February 2005 X Protocol Version 11, Revision 0, Release 6.8.2 Build Operating System: SunOS 5.10 Generic i86pc Current Operating System: SunOS dhcp-161-170 5.10 Generic_118844-19 i86pc Build Date: 02 August 2005 SUNWxorg-server package version: 6.8.0.5.10.7400,REV=0.2004.12.15 SUNWxorg-server patches applied: 118966-07 119062-01 118966-08 SUNWxorg-graphics-ddx package version: 6.8.0.5.10.7400,REV=0.2004.12.15 SUNWxorg-graphics-ddx patches applied: 118966-07 118966-08 Before reporting problems, check http://sunsolve.sun.com/ to make sure that you have the latest version. Module Loader present Markers: (--) probed, (**) from config file, (==) default setting, (++) from command line, (!!) notice, (II) informational, (WW) warning, (EE) error, (NI) not implemented, (??) unknown. (==) Log file: "/var/log/Xorg.0.log", Time: Thu Oct 13 16:40:44 2005 (==) Using config file: "/etc/X11/xorg.conf" (==) ServerLayout "Simple Layout" (**) |-->Screen "Screen 1" (0) (**) | |-->Monitor "NVIDIA NV28 32MB custom" (**) | |-->Device "** NVIDIA" (**) |-->Input Device "Mouse1" (**) |-->Input Device "Keyboard1" (**) Option "AutoRepeat" "500 30" (**) Option "XkbRules" "xorg" (**) XKB: rules: "xorg" (**) Option "XkbModel" "inspiron" (**) XKB: model: "inspiron" (**) Option "XkbLayout" "en_US" (**) XKB: layout: "en_US" (==) Keyboard: CustomKeycode disabled (**) FontPath set to "/usr/X11/lib/X11/fonts/TrueType/,/usr/X11/lib/X11/fonts/Type1/,/usr/X11/lib/X11/fonts/Type1/sun/,/usr/X11/lib/X11/fonts/F3bitmaps/,/usr/X11/lib/X11/fonts/misc/,/usr/X11/lib/X11/fonts/100dpi/,/usr/X11/lib/X11/fonts/75dpi/" (**) RgbPath set to "/usr/X11/lib/X11/rgb" (==) ModulePath set to "/usr/X11/lib/modules" (II) Module ABI versions: X.Org ANSI C Emulation: 0.2 X.Org Video Driver: 0.7 X.Org XInput driver : 0.4 X.Org Server Extension : 0.2 X.Org Font Renderer : 0.4 (II) Loader running on solaris (II) LoadModule: "bitmap" (II) Loading /usr/X11/lib/modules/fonts/libbitmap.so (II) Module bitmap: vendor="X.Org Foundation" compiled for 6.8.0, module version = 1.0.0 Module class: X.Org Font Renderer ABI class: X.Org Font Renderer, version 0.4 (II) Loading font Bitmap (II) LoadModule: "pcidata" (II) Loading /usr/X11/lib/modules/libpcidata.so (II) Module pcidata: vendor="X.Org Foundation" compiled for 6.8.0, module version = 1.0.0 ABI class: X.Org Video Driver, version 0.7 <snip> (II) LoadModule: "dbe" (II) Loading /usr/X11/lib/modules/extensions/libdbe.so (II) Module dbe: vendor="X.Org Foundation" compiled for 6.8.0, module version = 1.0.0 Module class: X.Org Server Extension ABI class: X.Org Server Extension, version 0.2 (II) Loading extension DOUBLE-BUFFER (II) LoadModule: "extmod" (II) Loading /usr/X11/lib/modules/extensions/libextmod.so (II) Module extmod: vendor="X.Org Foundation" compiled for 6.8.2, module version = 1.0.0 Module class: X.Org Server Extension ABI class: X.Org Server Extension, version 0.2 (II) Loading extension SHAPE (II) Loading extension MIT-SUNDRY-NONSTANDARD <snip> (II) Setting vga for screen 0. (++) NVIDIA(0): Depth 24, (--) framebuffer bpp 32 (==) NVIDIA(0): RGB weight 888 (==) NVIDIA(0): Default visual is TrueColor (==) NVIDIA(0): Using gamma correction (1.0, 1.0, 1.0) (**) NVIDIA(0): Option "FlatPanelProperties" "Scaling = aspect-scaled" (**) NVIDIA(0): FlatPanelProperties string: "Scaling = aspect-scaled" (--) NVIDIA(0): Linear framebuffer at 0xF0000000 (--) NVIDIA(0): MMIO registers at 0xFC000000 (II) NVIDIA(0): NVIDIA GPU detected as: GeForce4 4200 Go (--) NVIDIA(0): VideoBIOS: 04.28.20.31.c1 (--) NVIDIA(0): Interlaced video modes are supported on this GPU (II) NVIDIA(0): Detected AGP rate: 4X (--) NVIDIA(0): VideoRAM: 32768 kBytes (II) NVIDIA(0): Connected display device(s): DFP-0 (--) NVIDIA(0): DFP-0: maximum pixel clock: 165 MHz (--) NVIDIA(0): DFP-0: External Dual Link LVDS (II) Loading sub module "ddc" (II) LoadModule: "ddc" (II) Loading /usr/X11/lib/modules/libddc.so (II) Module ddc: vendor="X.Org Foundation" compiled for 6.8.2, module version = 1.0.0 ABI class: X.Org Video Driver, version 0.7 (WW) NVIDIA(0): config file hsync range 28-110kHz not within DDC hsync ranges. (WW) NVIDIA(0): config file vrefresh range 43-90Hz not within DDC vrefresh ranges. (II) NVIDIA(0): NVIDIA NV28 32MB custom: Using hsync range of 28.00-110.00 kHz (II) NVIDIA(0): NVIDIA NV28 32MB custom: Using vrefresh range of 43.00-90.00 Hz (II) NVIDIA(0): Clock range: 12.00 to 165.00 MHz (II) NVIDIA(0): Not using default mode "1600x1200" (bad mode clock/interlace/doublescan) (II) NVIDIA(0): Not using default mode "1600x1200" (bad mode clock/interlace/doublescan) (II) NVIDIA(0): Not using default mode "1600x1200" (bad mode clock/interlace/doublescan) (II) NVIDIA(0): Not using default mode "1600x1200" (bad mode clock/interlace/doublescan) (II) NVIDIA(0): Not using default mode "1792x1344" (height too large for virtual size) (II) NVIDIA(0): Not using default mode "1792x1344" (height too large for virtual size) (II) NVIDIA(0): Not using default mode "1856x1392" (height too large for virtual size) (II) NVIDIA(0): Not using default mode "1856x1392" (height too large for virtual size) (II) NVIDIA(0): Not using default mode "928x696" (hsync out of range) (II) NVIDIA(0): Not using default mode "1920x1440" (height too large for virtual size) (II) NVIDIA(0): Not using default mode "1920x1440" (height too large for virtual size) (II) NVIDIA(0): Not using default mode "960x720" (hsync out of range) (II) NVIDIA(0): Not using default mode "1920x1440" (height too large for virtual size) (II) NVIDIA(0): Not using default mode "960x720" (bad mode clock/interlace/doublescan) (II) NVIDIA(0): Not using default mode "2048x1536" (width too large for virtual size) (II) NVIDIA(0): Not using default mode "2048x1536" (width too large for virtual size) (II) NVIDIA(0): Not using default mode "1024x768" (bad mode clock/interlace/doublescan) (II) NVIDIA(0): Not using default mode "2048x1536" (width too large for virtual size) (II) NVIDIA(0): Not using default mode "1024x768" (bad mode clock/interlace/doublescan) (WW) NVIDIA(0): Not using mode "1024x768" (height 1536 is larger than (WW) NVIDIA(0): EDID-specified maximum 1200) (WW) NVIDIA(0): Not using mode "960x720" (height 1440 is larger than (WW) NVIDIA(0): EDID-specified maximum 1200) (WW) NVIDIA(0): Not using mode "928x696" (height 1392 is larger than (WW) NVIDIA(0): EDID-specified maximum 1200) (WW) NVIDIA(0): Not using mode "896x672" (height 1344 is larger than (WW) NVIDIA(0): EDID-specified maximum 1200) (WW) NVIDIA(0): Not using mode "896x672" (height 1344 is larger than (WW) NVIDIA(0): EDID-specified maximum 1200) (WW) NVIDIA(0): Not using mode "1152x768": (WW) NVIDIA(0): horizontal sync start (1178) not a multiple of 8 (WW) NVIDIA(0): Not using mode "960x600": (WW) NVIDIA(0): horizontal blanking width ((max(1258,1086) - min(960,968) = (WW) NVIDIA(0): 298) not a multiple of 8 (WW) NVIDIA(0): horizontal sync width (1086 - 968 = 118) not a multiple of (WW) NVIDIA(0): 8 (WW) NVIDIA(0): horizontal frame length (1258) not a multiple of 8 (WW) NVIDIA(0): Not using mode "576x384": (WW) NVIDIA(0): horizontal sync start (589) not a multiple of 8 (WW) NVIDIA(0): Not using mode "360x200": (WW) NVIDIA(0): horizontal sync start (378) not a multiple of 8 (**) NVIDIA(0): Validated modes for display device DFP-0: (**) NVIDIA(0): Mode "1920x1200": 162.0 MHz, 65.3 kHz, 52.3 Hz (**) NVIDIA(0): Default mode "1400x1050": 155.8 MHz, 81.5 kHz, 74.8 Hz (**) NVIDIA(0): Default mode "1600x1200": 162.0 MHz, 75.0 kHz, 60.0 Hz (**) NVIDIA(0): Default mode "1280x1024": 157.5 MHz, 91.1 kHz, 85.0 Hz (**) NVIDIA(0): Default mode "640x400": 31.5 MHz, 37.9 kHz, 85.1 Hz (**) NVIDIA(0): Default mode "1400x1050": 122.0 MHz, 64.9 kHz, 60.0 Hz (**) NVIDIA(0): Default mode "1280x1024": 135.0 MHz, 80.0 kHz, 75.0 Hz (**) NVIDIA(0): Default mode "1280x1024": 108.0 MHz, 64.0 kHz, 60.0 Hz (**) NVIDIA(0): Default mode "1280x960": 148.5 MHz, 85.9 kHz, 85.0 Hz (**) NVIDIA(0): Default mode "1280x960": 108.0 MHz, 60.0 kHz, 60.0 Hz (**) NVIDIA(0): Default mode "1152x864": 108.0 MHz, 67.5 kHz, 75.0 Hz (**) NVIDIA(0): Default mode "1024x768": 94.5 MHz, 68.7 kHz, 85.0 Hz (**) NVIDIA(0): Default mode "1024x768": 78.8 MHz, 60.1 kHz, 75.1 Hz (**) NVIDIA(0): Default mode "1024x768": 75.0 MHz, 56.5 kHz, 70.1 Hz (**) NVIDIA(0): Default mode "1024x768": 65.0 MHz, 48.4 kHz, 60.0 Hz (**) NVIDIA(0): Default mode "1024x768": 44.9 MHz, 35.5 kHz, 87.0 Hz (I) (**) NVIDIA(0): Default mode "832x624": 57.3 MHz, 49.7 kHz, 74.6 Hz (**) NVIDIA(0): Default mode "800x600": 56.3 MHz, 53.7 kHz, 85.1 Hz (**) NVIDIA(0): Default mode "800x600": 114.8 MHz, 106.2 kHz, 85.0 Hz (D) (**) NVIDIA(0): Default mode "800x600": 49.5 MHz, 46.9 kHz, 75.0 Hz (**) NVIDIA(0): Default mode "800x600": 101.2 MHz, 93.8 kHz, 75.0 Hz (D) (**) NVIDIA(0): Default mode "800x600": 50.0 MHz, 48.1 kHz, 72.2 Hz (**) NVIDIA(0): Default mode "800x600": 94.5 MHz, 87.5 kHz, 70.0 Hz (D) (**) NVIDIA(0): Default mode "800x600": 87.8 MHz, 81.2 kHz, 65.0 Hz (D) (**) NVIDIA(0): Default mode "800x600": 40.0 MHz, 37.9 kHz, 60.3 Hz (**) NVIDIA(0): Default mode "800x600": 81.0 MHz, 75.0 kHz, 60.0 Hz (D) (**) NVIDIA(0): Default mode "800x600": 36.0 MHz, 35.2 kHz, 56.2 Hz (**) NVIDIA(0): Default mode "700x525": 77.9 MHz, 81.5 kHz, 74.8 Hz (D) (**) NVIDIA(0): Default mode "700x525": 61.0 MHz, 64.9 kHz, 60.0 Hz (D) (**) NVIDIA(0): Default mode "640x512": 78.8 MHz, 91.1 kHz, 85.0 Hz (D) (**) NVIDIA(0): Default mode "640x512": 67.5 MHz, 80.0 kHz, 75.0 Hz (D) (**) NVIDIA(0): Default mode "640x512": 54.0 MHz, 64.0 kHz, 60.0 Hz (D) (**) NVIDIA(0): Default mode "640x480": 74.2 MHz, 85.9 kHz, 85.1 Hz (D) (**) NVIDIA(0): Default mode "640x480": 36.0 MHz, 43.3 kHz, 85.0 Hz (**) NVIDIA(0): Default mode "640x480": 31.5 MHz, 37.5 kHz, 75.0 Hz (**) NVIDIA(0): Default mode "640x480": 31.5 MHz, 37.9 kHz, 72.8 Hz (**) NVIDIA(0): Default mode "640x480": 25.2 MHz, 31.5 kHz, 60.0 Hz (**) NVIDIA(0): Default mode "640x480": 54.0 MHz, 60.0 kHz, 60.0 Hz (D) (**) NVIDIA(0): Default mode "720x400": 35.5 MHz, 37.9 kHz, 85.0 Hz (**) NVIDIA(0): Default mode "576x432": 54.0 MHz, 67.5 kHz, 75.0 Hz (D) (**) NVIDIA(0): Default mode "640x350": 31.5 MHz, 37.9 kHz, 85.1 Hz (**) NVIDIA(0): Default mode "512x384": 47.2 MHz, 68.7 kHz, 85.0 Hz (D) (**) NVIDIA(0): Default mode "512x384": 39.4 MHz, 60.1 kHz, 75.1 Hz (D) (**) NVIDIA(0): Default mode "512x384": 37.5 MHz, 56.5 kHz, 70.1 Hz (D) (**) NVIDIA(0): Default mode "512x384": 32.5 MHz, 48.4 kHz, 60.0 Hz (D) (**) NVIDIA(0): Default mode "512x384": 22.4 MHz, 35.5 kHz, 86.9 Hz (D) (**) NVIDIA(0): Default mode "416x312": 28.6 MHz, 49.7 kHz, 74.7 Hz (D) (**) NVIDIA(0): Default mode "400x300": 28.1 MHz, 53.7 kHz, 85.3 Hz (D) (**) NVIDIA(0): Default mode "400x300": 24.8 MHz, 46.9 kHz, 75.1 Hz (D) (**) NVIDIA(0): Default mode "400x300": 25.0 MHz, 48.1 kHz, 72.2 Hz (D) (**) NVIDIA(0): Default mode "400x300": 20.0 MHz, 37.9 kHz, 60.3 Hz (D) (**) NVIDIA(0): Default mode "400x300": 18.0 MHz, 35.2 kHz, 56.3 Hz (D) (**) NVIDIA(0): Default mode "320x240": 18.0 MHz, 43.3 kHz, 85.2 Hz (D) (**) NVIDIA(0): Default mode "320x240": 15.8 MHz, 37.5 kHz, 75.0 Hz (D) (**) NVIDIA(0): Default mode "320x240": 15.8 MHz, 37.9 kHz, 72.8 Hz (D) (**) NVIDIA(0): Default mode "320x240": 12.6 MHz, 31.5 kHz, 60.1 Hz (D) (**) NVIDIA(0): Default mode "320x200": 15.8 MHz, 37.9 kHz, 85.3 Hz (D) (**) NVIDIA(0): Default mode "320x175": 15.8 MHz, 37.9 kHz, 85.3 Hz (D) (--) NVIDIA(0): Display dimensions: (330, 210) mm (--) NVIDIA(0): DPI set to (147, 145) <snip> (II) NVIDIA(0): Setting mode "1920x1200" (II) Loading extension NV-GLX (II) NVIDIA(0): NVIDIA 3D Acceleration Architecture Initialized (II) NVIDIA(0): Using the NVIDIA 2D acceleration architecture (==) NVIDIA(0): Backing store disabled (==) NVIDIA(0): Silken mouse disabled (II) Loading extension NV-CONTROL (==) RandR enabled (II) Initializing built-in extension MIT-SHM (II) Initializing built-in extension XInputExtension (II) Initializing built-in extension XTEST (II) Initializing built-in extension XKEYBOARD (II) Initializing built-in extension LBX (II) Initializing built-in extension XC-APPGROUP (II) Initializing built-in extension SECURITY (II) Initializing built-in extension XINERAMA (II) Initializing built-in extension XFIXES (II) Initializing built-in extension XFree86-Bigfont (II) Initializing built-in extension RENDER (II) Initializing built-in extension RANDR (II) Initializing built-in extension COMPOSITE (II) Initializing built-in extension DAMAGE (II) Initializing built-in extension XEVIE (II) Initializing extension GLX (**) Option "Protocol" "Auto" (II) Mouse1: Setting Device option to "/dev/mouse" (**) Mouse1: Protocol: VUID (**) Option "CorePointer" (**) Mouse1: Core Pointer (**) Option "Device" "/dev/mouse" (II) Mouse1: Setting Buttons option to "3" (==) Mouse1: Emulate3Buttons, Emulate3Timeout: 50 (**) Option "ZAxisMapping" "4 5" (**) Mouse1: ZAxisMapping: buttons 4 and 5 (**) Mouse1: Buttons: 5 (II) XINPUT: Adding extended input device "Mouse1" (type: MOUSE) (II) XINPUT: Adding extended input device "NVIDIA Event Handler" (type: Other) (II) XINPUT: Adding extended input device "NVIDIA Kernel Input Handler" (type: Other) (--) Keyboard type: USB (6) (--) Keyboard layout: 33 (II) NVIDIA(0): Setting mode "1280x1024" AUDIT: Thu Oct 13 16:41:04 2005: 523 Xorg: client 9 rejected from local host AUDIT: Thu Oct 13 16:41:06 2005: 523 Xorg: client 10 rejected from local host |
|
|
|
|
10-13-05, 07:52 PM
|
#4 |
|
Registered User
Join Date: Oct 2005
Location: San Diego, CA
Posts: 12
|
Re: Cannot get 1920x1200 on D800 (wrong virtual size)
And here is the current /etc/X11/xorg.conf file:
# Generated by root on dhcp-161-170 at Tue Oct 4 13:54:28 2005 # File generated by xorgconfig. # # Copyright 2004 The X.Org Foundation # # Except as contained in this notice, the name of The X.Org Foundation shall # not be used in advertising or otherwise to promote the sale, use or other # dealings in this Software without prior written authorization from # The X.Org Foundation. # # ************************************************** ******************** # Refer to the xorg.conf(4) man page for details about the format of # this file. # ************************************************** ******************** # ************************************************** ******************** # Module section -- this section is used to specify # which dynamically loadable modules to load. # ************************************************** ******************** # Section "Module" # This loads the DBE extension module. Load "dbe" # Double buffer extension # This loads the miscellaneous extensions module, and disables # initialisation of the XFree86-DGA extension within that module. SubSection "extmod" Option "omit xfree86-dga" # don't initialise the DGA extension EndSubSection # This loads the font modules Load "bitstream" Load "type1" # Load "speedo" # This loads the Xst module Load "Xst" # This loads the SolarisIA module Load "IA" # This loads the GLX module Load "glx" EndSection # ************************************************** ******************** # Files section. This allows default font and rgb paths to be set # ************************************************** ******************** Section "Files" # The location of the RGB database. Note, this is the name of the # file minus the extension (like ".txt" or ".db"). There is normally # no need to change the default. RgbPath "/usr/X11/lib/X11/rgb" # Multiple FontPath entries are allowed (which are concatenated together), # as well as specifying multiple comma-separated entries in one FontPath # command (or a combination of both methods) # # FontPath "/usr/X11/lib/X11/fonts/TrueType/" FontPath "/usr/X11/lib/X11/fonts/Type1/" FontPath "/usr/X11/lib/X11/fonts/Type1/sun/" FontPath "/usr/X11/lib/X11/fonts/F3bitmaps/" FontPath "/usr/X11/lib/X11/fonts/misc/" FontPath "/usr/X11/lib/X11/fonts/100dpi/" FontPath "/usr/X11/lib/X11/fonts/75dpi/" # FontPath "/usr/X11/lib/X11/fonts/local/" # FontPath "/usr/X11/lib/X11/fonts/Speedo/" # FontPath "/usr/X11/lib/X11/fonts/freefont/" # The module search path. The default path is shown here. # ModulePath "/usr/X11/lib/modules" EndSection # ************************************************** ******************** # Server flags section. # ************************************************** ******************** Section "ServerFlags" # Uncomment this to cause a core dump at the spot where a signal is # received. This may leave the console in an unusable state, but may # provide a better stack trace in the core dump to aid in debugging # Option "NoTrapSignals" # Uncomment this to disable the <Crtl><Alt><Fn> VT switch sequence # (where n is 1 through 12). This allows clients to receive these key # events. # Option "DontVTSwitch" # Uncomment this to disable the <Crtl><Alt><BS> server abort sequence # This allows clients to receive this key event. # Option "DontZap" # Uncomment this to disable the <Crtl><Alt><KP_+>/<KP_-> mode switching # sequences. This allows clients to receive these key events. # Option "Dont Zoom" # Uncomment this to disable tuning with the xvidtune client. With # it the client can still run and fetch card and monitor attributes, # but it will not be allowed to change them. If it tries it will # receive a protocol error. # Option "DisableVidModeExtension" # Uncomment this to enable the use of a non-local xvidtune client. # Option "AllowNonLocalXvidtune" # Uncomment this to disable dynamically modifying the input device # (mouse and keyboard) settings. # Option "DisableModInDev" # Uncomment this to enable the use of a non-local client to # change the keyboard or mouse settings (currently only xset). # Option "AllowNonLocalModInDev" EndSection # ************************************************** ******************** # Input devices # ************************************************** ******************** # ************************************************** ******************** # Core keyboard's InputDevice section # ************************************************** ******************** Section "InputDevice" Identifier "Keyboard1" Driver "Keyboard" # For most OSs the protocol can be omitted (it defaults to "Standard"). # When using XQUEUE (only for SVR3 and SVR4, but not Solaris), # uncomment the following line. # Option "Protocol" "Xqueue" Option "AutoRepeat" "500 30" # Specify which keyboard LEDs can be user-controlled (eg, with xset(1)) # Option "Xleds" "1 2 3" # Option "LeftAlt" "Meta" # Option "RightAlt" "ModeShift" # To customise the XKB settings to suit your keyboard, modify the # lines below (which are the defaults). For example, for a non-U.S. # keyboard, you will probably want to use: # Option "XkbModel" "pc102" # If you have a US Microsoft Natural keyboard, you can use: # Option "XkbModel" "microsoft" # # Then to change the language, change the Layout setting. # For example, a german layout can be obtained with: # Option "XkbLayout" "de" # or: # Option "XkbLayout" "de" # Option "XkbVariant" "nodeadkeys" # # If you'd like to switch the positions of your capslock and # control keys, use: # Option "XkbOptions" "ctrl:swapcaps" # These are the default XKB settings for Xorg # Option "XkbRules" "xorg" # Option "XkbModel" "pc101" # Option "XkbLayout" "us" # Option "XkbVariant" "" # Option "XkbOptions" "" # Option "XkbDisable" Option "XkbRules" "xorg" Option "XkbModel" "inspiron" Option "XkbLayout" "en_US" EndSection # ************************************************** ******************** # Core Pointer's InputDevice section # ************************************************** ******************** Section "InputDevice" # Identifier and driver Identifier "Mouse1" Driver "mouse" Option "Protocol" "Auto" Option "Device" "/dev/mouse" # Mouse-speed setting for PS/2 mouse. # Option "Resolution" "256" # When using XQUEUE, comment out the above two lines, and uncomment # the following line. # Option "Protocol" "Xqueue" # Baudrate and SampleRate are only for some Logitech mice. In # almost every case these lines should be omitted. # Option "BaudRate" "9600" # Option "SampleRate" "150" # Emulate3Buttons is an option for 2-button Microsoft mice # Emulate3Timeout is the timeout in milliseconds (default is 50ms) # Option "Emulate3Buttons" # Option "Emulate3Timeout" "50" # ChordMiddle is an option for some 3-button Logitech mice # Option "ChordMiddle" EndSection # ************************************************** ******************** # Other input device sections # this is optional and is required only if you # are using extended input devices. This is for example only. Refer # to the xorg.conf man page for a description of the options. # ************************************************** ******************** # # Section "InputDevice" # Identifier "Mouse2" # Driver "mouse" # Option "Protocol" "MouseMan" # Option "Device" "/dev/mouse2" # EndSection # # Section "InputDevice" # Identifier "spaceball" # Driver "magellan" # Option "Device" "/dev/cua0" # EndSection # # Section "InputDevice" # Identifier "spaceball2" # Driver "spaceorb" # Option "Device" "/dev/cua0" # EndSection # # Section "InputDevice" # Identifier "touchscreen0" # Driver "microtouch" # Option "Device" "/dev/ttyS0" # Option "MinX" "1412" # Option "MaxX" "15184" # Option "MinY" "15372" # Option "MaxY" "1230" # Option "ScreenNumber" "0" # Option "ReportingMode" "Scaled" # Option "ButtonNumber" "1" # Option "SendCoreEvents" # EndSection # # Section "InputDevice" # Identifier "touchscreen1" # Driver "elo2300" # Option "Device" "/dev/ttyS0" # Option "MinX" "231" # Option "MaxX" "3868" # Option "MinY" "3858" # Option "MaxY" "272" # Option "ScreenNumber" "0" # Option "ReportingMode" "Scaled" # Option "ButtonThreshold" "17" # Option "ButtonNumber" "1" # Option "SendCoreEvents" # EndSection # ************************************************** ******************** # Monitor section # ************************************************** ******************** # Any number of monitor sections may be present # from http://www.linuxquestions.org/questi...04/07/3/195620 Section "Monitor" Identifier "NVIDIA NV28 32MB custom" # HorizSync is in kHz unless units are specified. HorizSync 28-110 # VertRefresh is in Hz unless units are specified. VertRefresh 43-90 # DisplaySize 344.5 222.5 # Option "DPMS" Modeline "1920x1200" 162 1920 1984 2176 2480 1200 1201 1204 1250 +hsync +vsync EndSection # ************************************************** ******************** # Graphics device section # ************************************************** ******************** # Any number of graphics device sections may be present # Standard VGA Device: Section "Device" Identifier "Standard VGA" VendorName "Unknown" BoardName "Unknown" # The chipset line is optional in most cases. It can be used to override # the driver's chipset detection, and should not normally be specified. # Chipset "generic" # The Driver line must be present. When using run-time loadable driver # modules, this line instructs the server to load the specified driver # module. Even when not using loadable driver modules, this line # indicates which driver should interpret the information in this section. Driver "vga" # The BusID line is used to specify which of possibly multiple devices # this section is intended for. When this line isn't present, a device # section can only match up with the primary video device. For PCI # devices a line like the following could be used. This line should not # normally be included unless there is more than one video device # intalled. # BusID "PCI:0:10:0" # VideoRam 256 # Clocks 25.2 28.3 EndSection # Device configured by xorgconfig: Section "Device" Identifier "** NVIDIA" Driver "nvidia" # Option "DPMS" EndSection # ************************************************** ******************** # Screen sections # ************************************************** ******************** # Any number of screen sections may be present. Each describes # the configuration of a single screen. A single specific screen section # may be specified from the X server command line with the "-screen" # option. Section "Screen" Identifier "Screen 1" Device "** NVIDIA" Monitor "NVIDIA NV28 32MB custom" DefaultDepth 24 # Option "IgnoreEDID" "true" # Option "FlatPanelProperties" "Scaling=centered" Option "FlatPanelProperties" "Scaling = aspect-scaled" Subsection "Display" Depth 8 Virtual 1920 1200 Modes "1920x1200" "1280x1024" "1024x768" "800x600" "640x480" ViewPort 0 0 EndSubsection Subsection "Display" Depth 16 Virtual 1920 1200 Modes "1920x1200" "1400x1050" "1600x1200" "1280x1024" "1024x768" "640x400" ViewPort 0 0 EndSubsection Subsection "Display" Depth 24 Virtual 1920 1200 Modes "1920x1200" "1400x1050" "1600x1200" "1280x1024" "640x400" ViewPort 0 0 EndSubsection EndSection # ************************************************** ******************** # ServerLayout sections. # ************************************************** ******************** # Any number of ServerLayout sections may be present. Each describes # the way multiple screens are organised. A specific ServerLayout # section may be specified from the X server command line with the # "-layout" option. In the absence of this, the first section is used. # When now ServerLayout section is present, the first Screen section # is used alone. Section "ServerLayout" # The Identifier line must be present Identifier "Simple Layout" # Each Screen line specifies a Screen section name, and optionally # the relative position of other screens. The four names after # primary screen name are the screens to the top, bottom, left and right # of the primary screen. In this example, screen 2 is located to the # right of screen 1. Screen "Screen 1" # Each InputDevice line specifies an InputDevice section name and # optionally some options to specify the way the device is to be # used. Those options include "CorePointer", "CoreKeyboard" and # "SendCoreEvents". InputDevice "Mouse1" "CorePointer" InputDevice "Keyboard1" "CoreKeyboard" EndSection # Section "DRI" # Mode 0666 # EndSection |
|
|
|
|
10-14-05, 06:12 AM
|
#5 |
|
NVIDIA Corporation
Join Date: Aug 2002
Posts: 3,677
|
Re: Cannot get 1920x1200 on D800 (wrong virtual size)
@catalan: which resolution did you specify in the JDE preferences (Launch -> Preferences -> Desktop Preferences -> Display -> Screen Resolution) for your user?
|
|
|
|
|
10-17-05, 01:54 PM
|
#6 |
|
Registered User
Join Date: Oct 2005
Location: San Diego, CA
Posts: 12
|
Re: Cannot get 1920x1200 on D800 (wrong virtual size)
OK - I got it working at full resolution! The problem appears to have been bad(?) desktop files. I deleted all the following files and forced the system to re-create them:
/.ICEauthority /.Xauthority /.dt /.dtprofile /.gconf /.gconf-csw /.gconfd /.gnome /.gnome2 /.gnome2_private /.gnupg /.gtkrc-1.2-gnome2 /.smc.properties /.sunw It appears that my /etc/X11/xorg.conf was OK after all (after a lot of tweaking). The strange part is that the /var/log/Xorg.0.log first said it was in 1920x1200 mode, then switched later to 1280x1024. I now believe that something in the /.dt or other files was causing this switch back from max resolution. Trying to change the resolution via JDE preferences (Launch -> Preferences -> Desktop Preferences -> Display -> Screen Resolution) did not show an option larger than 1280x1024, though. So, I was perplexed and found the answer only by luck. Everything is working great now. Alan Thompson |
|
|
|
|
10-17-05, 02:02 PM
|
#7 |
|
Registered User
Join Date: Oct 2005
Location: San Diego, CA
Posts: 12
|
Re: Cannot get 1920x1200 on D800 (wrong virtual size)
More info:
 This works at 1920x1200 resolution (i.e. WUXGA) on a Dell D800 running Solaris 10, with all patches as of 2005-10-17. I am using the new "nvidia" driver (not the "nv" driver) installed by following the instrucitons at http://www.nvnews.net/vbulletin/showthread.php?t=52257. Video card is: nVidia Corporation NV28 [GeForce4 Ti 4200 Go AGP 8x] rev 161 NVIDIA(0): VideoRAM: 32768 kBytes Here is my working /etc/X11/xorg.conf file: # Generated by root on dhcp-161-170 at Tue Oct 4 13:54:28 2005 # ************************************************** ******************** # Refer to the xorg.conf(4) man page for details about the format of # this file. # ************************************************** ******************** # ************************************************** ******************** # Module section -- this section is used to specify # which dynamically loadable modules to load. # ************************************************** ******************** # Section "Module" # This loads the DBE extension module. Load "dbe" # Double buffer extension # This loads the miscellaneous extensions module, and disables # initialisation of the XFree86-DGA extension within that module. SubSection "extmod" Option "omit xfree86-dga" # don't initialise the DGA extension EndSubSection # This loads the font modules Load "bitstream" Load "type1" # This loads the Xst module Load "Xst" # This loads the SolarisIA module Load "IA" # This loads the GLX module Load "glx" EndSection # ************************************************** ******************** # Files section. This allows default font and rgb paths to be set # ************************************************** ******************** Section "Files" # The location of the RGB database. Note, this is the name of the # file minus the extension (like ".txt" or ".db"). There is normally # no need to change the default. RgbPath "/usr/X11/lib/X11/rgb" # Multiple FontPath entries are allowed (which are concatenated together), # as well as specifying multiple comma-separated entries in one FontPath # command (or a combination of both methods) FontPath "/usr/X11/lib/X11/fonts/TrueType/" FontPath "/usr/X11/lib/X11/fonts/Type1/" FontPath "/usr/X11/lib/X11/fonts/Type1/sun/" FontPath "/usr/X11/lib/X11/fonts/F3bitmaps/" FontPath "/usr/X11/lib/X11/fonts/misc/" FontPath "/usr/X11/lib/X11/fonts/100dpi/" FontPath "/usr/X11/lib/X11/fonts/75dpi/" # FontPath "/usr/X11/lib/X11/fonts/local/" # FontPath "/usr/X11/lib/X11/fonts/Speedo/" # FontPath "/usr/X11/lib/X11/fonts/freefont/" # The module search path. The default path is shown here. # ModulePath "/usr/X11/lib/modules" EndSection # ************************************************** ******************** # Server flags section. # ************************************************** ******************** Section "ServerFlags" # Uncomment this to cause a core dump at the spot where a signal is # received. This may leave the console in an unusable state, but may # provide a better stack trace in the core dump to aid in debugging # Option "NoTrapSignals" # Uncomment this to disable the <Crtl><Alt><Fn> VT switch sequence # (where n is 1 through 12). This allows clients to receive these key # events. # Option "DontVTSwitch" # Uncomment this to disable the <Crtl><Alt><BS> server abort sequence # This allows clients to receive this key event. # Option "DontZap" # Uncomment this to disable the <Crtl><Alt><KP_+>/<KP_-> mode switching # sequences. This allows clients to receive these key events. # Option "Dont Zoom" # Uncomment this to disable tuning with the xvidtune client. With # it the client can still run and fetch card and monitor attributes, # but it will not be allowed to change them. If it tries it will # receive a protocol error. # Option "DisableVidModeExtension" # Uncomment this to enable the use of a non-local xvidtune client. # Option "AllowNonLocalXvidtune" # Uncomment this to disable dynamically modifying the input device # (mouse and keyboard) settings. # Option "DisableModInDev" # Uncomment this to enable the use of a non-local client to # change the keyboard or mouse settings (currently only xset). # Option "AllowNonLocalModInDev" EndSection # ************************************************** ******************** # Input devices # ************************************************** ******************** # ************************************************** ******************** # Core keyboard's InputDevice section # ************************************************** ******************** Section "InputDevice" Identifier "Keyboard1" Driver "Keyboard" # For most OSs the protocol can be omitted (it defaults to "Standard"). # When using XQUEUE (only for SVR3 and SVR4, but not Solaris), # uncomment the following line. # Option "Protocol" "Xqueue" Option "AutoRepeat" "500 30" # Specify which keyboard LEDs can be user-controlled (eg, with xset(1)) # Option "Xleds" "1 2 3" # Option "LeftAlt" "Meta" # Option "RightAlt" "ModeShift" # To customise the XKB settings to suit your keyboard, modify the # lines below (which are the defaults). For example, for a non-U.S. # keyboard, you will probably want to use: # Option "XkbModel" "pc102" # If you have a US Microsoft Natural keyboard, you can use: # Option "XkbModel" "microsoft" # # Then to change the language, change the Layout setting. # For example, a german layout can be obtained with: # Option "XkbLayout" "de" # or: # Option "XkbLayout" "de" # Option "XkbVariant" "nodeadkeys" # # If you'd like to switch the positions of your capslock and # control keys, use: # Option "XkbOptions" "ctrl:swapcaps" # These are the default XKB settings for Xorg # Option "XkbRules" "xorg" # Option "XkbModel" "pc101" # Option "XkbLayout" "us" # Option "XkbVariant" "" # Option "XkbOptions" "" # Option "XkbDisable" Option "XkbRules" "xorg" Option "XkbModel" "inspiron" Option "XkbLayout" "en_US" EndSection # ************************************************** ******************** # Core Pointer's InputDevice section # ************************************************** ******************** Section "InputDevice" # Identifier and driver Identifier "Mouse1" Driver "mouse" Option "Protocol" "Auto" Option "Device" "/dev/mouse" # Mouse-speed setting for PS/2 mouse. # Option "Resolution" "256" # When using XQUEUE, comment out the above two lines, and uncomment # the following line. # Option "Protocol" "Xqueue" # Baudrate and SampleRate are only for some Logitech mice. In # almost every case these lines should be omitted. # Option "BaudRate" "9600" # Option "SampleRate" "150" # Emulate3Buttons is an option for 2-button Microsoft mice # Emulate3Timeout is the timeout in milliseconds (default is 50ms) # Option "Emulate3Buttons" # Option "Emulate3Timeout" "50" # ChordMiddle is an option for some 3-button Logitech mice # Option "ChordMiddle" EndSection # ************************************************** ******************** # Other input device sections # this is optional and is required only if you # are using extended input devices. This is for example only. Refer # to the xorg.conf man page for a description of the options. # ************************************************** ******************** # # Section "InputDevice" # Identifier "Mouse2" # Driver "mouse" # Option "Protocol" "MouseMan" # Option "Device" "/dev/mouse2" # EndSection # # Section "InputDevice" # Identifier "spaceball" # Driver "magellan" # Option "Device" "/dev/cua0" # EndSection # # Section "InputDevice" # Identifier "spaceball2" # Driver "spaceorb" # Option "Device" "/dev/cua0" # EndSection # # Section "InputDevice" # Identifier "touchscreen0" # Driver "microtouch" # Option "Device" "/dev/ttyS0" # Option "MinX" "1412" # Option "MaxX" "15184" # Option "MinY" "15372" # Option "MaxY" "1230" # Option "ScreenNumber" "0" # Option "ReportingMode" "Scaled" # Option "ButtonNumber" "1" # Option "SendCoreEvents" # EndSection # # Section "InputDevice" # Identifier "touchscreen1" # Driver "elo2300" # Option "Device" "/dev/ttyS0" # Option "MinX" "231" # Option "MaxX" "3868" # Option "MinY" "3858" # Option "MaxY" "272" # Option "ScreenNumber" "0" # Option "ReportingMode" "Scaled" # Option "ButtonThreshold" "17" # Option "ButtonNumber" "1" # Option "SendCoreEvents" # EndSection # ************************************************** ******************** # Monitor section # ************************************************** ******************** # Any number of monitor sections may be present # from http://www.linuxquestions.org/questi...04/07/3/195620 Section "Monitor" Identifier "NVIDIA NV28 32MB custom" # HorizSync is in kHz unless units are specified. HorizSync 28-110 # VertRefresh is in Hz unless units are specified. VertRefresh 43-90 # DisplaySize 344.5 222.5 # Option "DPMS" Modeline "1920x1200" 162 1920 1984 2176 2480 1200 1201 1204 1250 +hsync +vsync EndSection # ************************************************** ******************** # Graphics device section # ************************************************** ******************** # Any number of graphics device sections may be present # Device configured by xorgconfig: Section "Device" Identifier "** NVIDIA" Driver "nvidia" # Option "DPMS" EndSection # ************************************************** ******************** # Screen sections # ************************************************** ******************** # Any number of screen sections may be present. Each describes # the configuration of a single screen. A single specific screen section # may be specified from the X server command line with the "-screen" # option. Section "Screen" Identifier "Screen 1" Device "** NVIDIA" Monitor "NVIDIA NV28 32MB custom" DefaultDepth 24 # Option "IgnoreEDID" "true" # Option "FlatPanelProperties" "Scaling=centered" # Option "FlatPanelProperties" "Scaling = aspect-scaled" Subsection "Display" Depth 8 Virtual 1920 1200 Modes "1920x1200" "1280x1024" "1024x768" "800x600" "640x480" ViewPort 0 0 EndSubsection Subsection "Display" Depth 16 Virtual 1920 1200 Modes "1920x1200" "1400x1050" "1600x1200" "1280x1024" "1024x768" "640x400" ViewPort 0 0 EndSubsection Subsection "Display" Depth 24 Virtual 1920 1200 Modes "1920x1200" "1400x1050" "1600x1200" "1280x1024" "640x400" ViewPort 0 0 EndSubsection EndSection # ************************************************** ******************** # ServerLayout sections. # ************************************************** ******************** # Any number of ServerLayout sections may be present. Each describes # the way multiple screens are organised. A specific ServerLayout # section may be specified from the X server command line with the # "-layout" option. In the absence of this, the first section is used. # When now ServerLayout section is present, the first Screen section # is used alone. Section "ServerLayout" # The Identifier line must be present Identifier "Simple Layout" # Each Screen line specifies a Screen section name, and optionally # the relative position of other screens. The four names after # primary screen name are the screens to the top, bottom, left and right # of the primary screen. In this example, screen 2 is located to the # right of screen 1. Screen "Screen 1" # Each InputDevice line specifies an InputDevice section name and # optionally some options to specify the way the device is to be # used. Those options include "CorePointer", "CoreKeyboard" and # "SendCoreEvents". InputDevice "Mouse1" "CorePointer" InputDevice "Keyboard1" "CoreKeyboard" EndSection |
|
|
|
|
10-17-05, 02:11 PM
|
#8 |
|
Registered User
Join Date: Oct 2005
Location: San Diego, CA
Posts: 12
|
Re: Cannot get 1920x1200 on D800 (wrong virtual size)
More info:
The working 1920x1200 modeline Modeline "1920x1200" 162 1920 1984 2176 2480 1200 1201 1204 1250 +hsync +vsync in the Monitor section is from linuxquestions.org I also switched from a default pixel depth of 16 bits to 24 bits in the "Screen" section - I don't know if this made any difference or not. # from http://www.linuxquestions.org/questi...04/07/3/195620 Code:
Section "Monitor"
Identifier "NVIDIA NV28 32MB custom"
# HorizSync is in kHz unless units are specified.
HorizSync 28-110
# VertRefresh is in Hz unless units are specified.
VertRefresh 43-90
# DisplaySize 344.5 222.5
# Option "DPMS"
Modeline "1920x1200" 162 1920 1984 2176 2480 1200 1201 1204 1250 +hsync +vsync
EndSection
|
|
|
|
|
10-17-05, 02:19 PM
|
#9 |
|
Registered User
Join Date: Oct 2005
Location: San Diego, CA
Posts: 12
|
Re: Cannot get 1920x1200 on D800 (wrong virtual size)
More Info: I have now deleted the 3 lines which read
Code:
Virtual 1920 1200 |
|
|
|
|
10-17-05, 02:30 PM
|
#10 |
|
Registered User
Join Date: Oct 2005
Location: San Diego, CA
Posts: 12
|
Re: Cannot get 1920x1200 on D800 (wrong virtual size)
Here is the working /var/log/Xorg.0.log file:
X Window System Version 6.8.2 (Sun Xorg Release 1.1 for Solaris 10) Release Date: 9 February 2005 X Protocol Version 11, Revision 0, Release 6.8.2 Build Operating System: SunOS 5.10 Generic i86pc Current Operating System: SunOS dhcp-161-170 5.10 Generic_118844-19 i86pc Build Date: 02 August 2005 SUNWxorg-server package version: 6.8.0.5.10.7400,REV=0.2004.12.15 SUNWxorg-server patches applied: 118966-07 119062-01 118966-08 SUNWxorg-graphics-ddx package version: 6.8.0.5.10.7400,REV=0.2004.12.15 SUNWxorg-graphics-ddx patches applied: 118966-07 118966-08 Before reporting problems, check http://sunsolve.sun.com/ to make sure that you have the latest version. Module Loader present Markers: (--) probed, (**) from config file, (==) default setting, (++) from command line, (!!) notice, (II) informational, (WW) warning, (EE) error, (NI) not implemented, (??) unknown. (==) Log file: "/var/log/Xorg.0.log", Time: Mon Oct 17 11:25:29 2005 (==) Using config file: "/etc/X11/xorg.conf" (==) ServerLayout "Simple Layout" (**) |-->Screen "Screen 1" (0) (**) | |-->Monitor "NVIDIA NV28 32MB custom" (**) | |-->Device "** NVIDIA" (**) |-->Input Device "Mouse1" (**) |-->Input Device "Keyboard1" (**) Option "AutoRepeat" "500 30" (**) Option "XkbRules" "xorg" (**) XKB: rules: "xorg" (**) Option "XkbModel" "inspiron" (**) XKB: model: "inspiron" (**) Option "XkbLayout" "en_US" (**) XKB: layout: "en_US" (==) Keyboard: CustomKeycode disabled <snip> (II) Loader running on solaris (II) LoadModule: "bitmap" (II) Loading /usr/X11/lib/modules/fonts/libbitmap.so (II) Module bitmap: vendor="X.Org Foundation" compiled for 6.8.0, module version = 1.0.0 Module class: X.Org Font Renderer ABI class: X.Org Font Renderer, version 0.4 <snip> (II) LoadModule: "glx" (II) Loading /usr/X11/lib/modules/extensions/libglx.so (II) Module glx: vendor="NVIDIA Corporation" compiled for 4.0.2, module version = 1.0.7676 Module class: X.Org Server Extension ABI class: X.Org Server Extension, version 0.1 (II) Loading extension GLX (II) LoadModule: "nvidia" (II) Loading /usr/X11/lib/modules/drivers/nvidia_drv.so (II) Module nvidia: vendor="NVIDIA Corporation" compiled for 4.0.2, module version = 1.0.7676 Module class: X.Org Video Driver (II) LoadModule: "mouse" (II) Loading /usr/X11/lib/modules/input/mouse_drv.so (II) Module mouse: vendor="X.Org Foundation" compiled for 6.8.0, module version = 1.0.0 Module class: X.Org XInput Driver ABI class: X.Org XInput driver, version 0.4 (II) LoadModule: "Keyboard" (WW) Warning, couldn't open module Keyboard (II) UnloadModule: "Keyboard" (EE) Failed to load module "Keyboard" (module does not exist, 0) (II) NVIDIA dlloader X Driver 1.0-7676 Fri Jul 29 13:25:02 PDT 2005 (II) NVIDIA Unified Driver for all NVIDIA GPUs (II) Primary Device is: PCI 01:00:0 (--) Assigning device section with no busID to primary device (--) Chipset NVIDIA GPU found <snip> (II) Setting vga for screen 0. (++) NVIDIA(0): Depth 24, (--) framebuffer bpp 32 (==) NVIDIA(0): RGB weight 888 (==) NVIDIA(0): Default visual is TrueColor (==) NVIDIA(0): Using gamma correction (1.0, 1.0, 1.0) (--) NVIDIA(0): Linear framebuffer at 0xF0000000 (--) NVIDIA(0): MMIO registers at 0xFC000000 (II) NVIDIA(0): NVIDIA GPU detected as: GeForce4 4200 Go (--) NVIDIA(0): VideoBIOS: 04.28.20.31.c1 (--) NVIDIA(0): Interlaced video modes are supported on this GPU (II) NVIDIA(0): Detected AGP rate: 4X (--) NVIDIA(0): VideoRAM: 32768 kBytes (II) NVIDIA(0): Connected display device(s): DFP-0 (--) NVIDIA(0): DFP-0: maximum pixel clock: 165 MHz (--) NVIDIA(0): DFP-0: Internal Single Link TMDS (II) Loading sub module "ddc" (II) LoadModule: "ddc" (II) Loading /usr/X11/lib/modules/libddc.so (II) Module ddc: vendor="X.Org Foundation" compiled for 6.8.2, module version = 1.0.0 ABI class: X.Org Video Driver, version 0.7 (WW) NVIDIA(0): config file hsync range 28-110kHz not within DDC hsync ranges. (WW) NVIDIA(0): config file vrefresh range 43-90Hz not within DDC vrefresh ranges. (II) NVIDIA(0): NVIDIA NV28 32MB custom: Using hsync range of 28.00-110.00 kHz (II) NVIDIA(0): NVIDIA NV28 32MB custom: Using vrefresh range of 43.00-90.00 Hz (II) NVIDIA(0): Clock range: 12.00 to 165.00 MHz (II) NVIDIA(0): Not using default mode "1600x1200" (bad mode clock/interlace/doublescan) (II) NVIDIA(0): Not using default mode "1600x1200" (bad mode clock/interlace/doublescan) (II) NVIDIA(0): Not using default mode "1600x1200" (bad mode clock/interlace/doublescan) (II) NVIDIA(0): Not using default mode "1600x1200" (bad mode clock/interlace/doublescan) (II) NVIDIA(0): Not using default mode "1792x1344" (bad mode clock/interlace/doublescan) (II) NVIDIA(0): Not using default mode "1792x1344" (bad mode clock/interlace/doublescan) (II) NVIDIA(0): Not using default mode "1856x1392" (bad mode clock/interlace/doublescan) (II) NVIDIA(0): Not using default mode "1856x1392" (bad mode clock/interlace/doublescan) (II) NVIDIA(0): Not using default mode "928x696" (hsync out of range) (II) NVIDIA(0): Not using default mode "1920x1440" (bad mode clock/interlace/doublescan) (II) NVIDIA(0): Not using default mode "1920x1440" (bad mode clock/interlace/doublescan) (II) NVIDIA(0): Not using default mode "960x720" (hsync out of range) (II) NVIDIA(0): Not using default mode "1920x1440" (bad mode clock/interlace/doublescan) (II) NVIDIA(0): Not using default mode "960x720" (bad mode clock/interlace/doublescan) (II) NVIDIA(0): Not using default mode "2048x1536" (bad mode clock/interlace/doublescan) (II) NVIDIA(0): Not using default mode "2048x1536" (bad mode clock/interlace/doublescan) (II) NVIDIA(0): Not using default mode "1024x768" (bad mode clock/interlace/doublescan) (II) NVIDIA(0): Not using default mode "2048x1536" (bad mode clock/interlace/doublescan) (II) NVIDIA(0): Not using default mode "1024x768" (bad mode clock/interlace/doublescan) (WW) NVIDIA(0): Not using mode "1024x768" (height 1536 is larger than (WW) NVIDIA(0): EDID-specified maximum 1200) (WW) NVIDIA(0): Not using mode "960x720" (height 1440 is larger than (WW) NVIDIA(0): EDID-specified maximum 1200) (WW) NVIDIA(0): Not using mode "928x696" (height 1392 is larger than (WW) NVIDIA(0): EDID-specified maximum 1200) (WW) NVIDIA(0): Not using mode "896x672" (height 1344 is larger than (WW) NVIDIA(0): EDID-specified maximum 1200) (WW) NVIDIA(0): Not using mode "896x672" (height 1344 is larger than (WW) NVIDIA(0): EDID-specified maximum 1200) (WW) NVIDIA(0): Not using mode "1152x768": (WW) NVIDIA(0): horizontal sync start (1178) not a multiple of 8 (WW) NVIDIA(0): Not using mode "960x600": (WW) NVIDIA(0): horizontal blanking width ((max(1258,1086) - min(960,968) = (WW) NVIDIA(0): 298) not a multiple of 8 (WW) NVIDIA(0): horizontal sync width (1086 - 968 = 118) not a multiple of (WW) NVIDIA(0): 8 (WW) NVIDIA(0): horizontal frame length (1258) not a multiple of 8 (WW) NVIDIA(0): Not using mode "576x384": (WW) NVIDIA(0): horizontal sync start (589) not a multiple of 8 (WW) NVIDIA(0): Not using mode "360x200": (WW) NVIDIA(0): horizontal sync start (378) not a multiple of 8 (**) NVIDIA(0): Validated modes for display device DFP-0: (**) NVIDIA(0): Mode "1920x1200": 162.0 MHz, 65.3 kHz, 52.3 Hz (**) NVIDIA(0): Default mode "1400x1050": 155.8 MHz, 81.5 kHz, 74.8 Hz (**) NVIDIA(0): Default mode "1600x1200": 162.0 MHz, 75.0 kHz, 60.0 Hz (**) NVIDIA(0): Default mode "1280x1024": 157.5 MHz, 91.1 kHz, 85.0 Hz (**) NVIDIA(0): Default mode "640x400": 31.5 MHz, 37.9 kHz, 85.1 Hz (**) NVIDIA(0): Default mode "1400x1050": 122.0 MHz, 64.9 kHz, 60.0 Hz (**) NVIDIA(0): Default mode "1280x1024": 135.0 MHz, 80.0 kHz, 75.0 Hz (**) NVIDIA(0): Default mode "1280x1024": 108.0 MHz, 64.0 kHz, 60.0 Hz (**) NVIDIA(0): Default mode "1280x960": 148.5 MHz, 85.9 kHz, 85.0 Hz (**) NVIDIA(0): Default mode "1280x960": 108.0 MHz, 60.0 kHz, 60.0 Hz (**) NVIDIA(0): Default mode "1152x864": 108.0 MHz, 67.5 kHz, 75.0 Hz (**) NVIDIA(0): Default mode "1024x768": 94.5 MHz, 68.7 kHz, 85.0 Hz (**) NVIDIA(0): Default mode "1024x768": 78.8 MHz, 60.1 kHz, 75.1 Hz (**) NVIDIA(0): Default mode "1024x768": 75.0 MHz, 56.5 kHz, 70.1 Hz (**) NVIDIA(0): Default mode "1024x768": 65.0 MHz, 48.4 kHz, 60.0 Hz (**) NVIDIA(0): Default mode "1024x768": 44.9 MHz, 35.5 kHz, 87.0 Hz (I) (**) NVIDIA(0): Default mode "832x624": 57.3 MHz, 49.7 kHz, 74.6 Hz (**) NVIDIA(0): Default mode "800x600": 56.3 MHz, 53.7 kHz, 85.1 Hz (**) NVIDIA(0): Default mode "800x600": 114.8 MHz, 106.2 kHz, 85.0 Hz (D) (**) NVIDIA(0): Default mode "800x600": 49.5 MHz, 46.9 kHz, 75.0 Hz (**) NVIDIA(0): Default mode "800x600": 101.2 MHz, 93.8 kHz, 75.0 Hz (D) (**) NVIDIA(0): Default mode "800x600": 50.0 MHz, 48.1 kHz, 72.2 Hz (**) NVIDIA(0): Default mode "800x600": 94.5 MHz, 87.5 kHz, 70.0 Hz (D) (**) NVIDIA(0): Default mode "800x600": 87.8 MHz, 81.2 kHz, 65.0 Hz (D) (**) NVIDIA(0): Default mode "800x600": 40.0 MHz, 37.9 kHz, 60.3 Hz (**) NVIDIA(0): Default mode "800x600": 81.0 MHz, 75.0 kHz, 60.0 Hz (D) (**) NVIDIA(0): Default mode "800x600": 36.0 MHz, 35.2 kHz, 56.2 Hz (**) NVIDIA(0): Default mode "700x525": 77.9 MHz, 81.5 kHz, 74.8 Hz (D) (**) NVIDIA(0): Default mode "700x525": 61.0 MHz, 64.9 kHz, 60.0 Hz (D) (**) NVIDIA(0): Default mode "640x512": 78.8 MHz, 91.1 kHz, 85.0 Hz (D) (**) NVIDIA(0): Default mode "640x512": 67.5 MHz, 80.0 kHz, 75.0 Hz (D) (**) NVIDIA(0): Default mode "640x512": 54.0 MHz, 64.0 kHz, 60.0 Hz (D) (**) NVIDIA(0): Default mode "640x480": 74.2 MHz, 85.9 kHz, 85.1 Hz (D) (**) NVIDIA(0): Default mode "640x480": 36.0 MHz, 43.3 kHz, 85.0 Hz (**) NVIDIA(0): Default mode "640x480": 31.5 MHz, 37.5 kHz, 75.0 Hz (**) NVIDIA(0): Default mode "640x480": 31.5 MHz, 37.9 kHz, 72.8 Hz (**) NVIDIA(0): Default mode "640x480": 25.2 MHz, 31.5 kHz, 60.0 Hz (**) NVIDIA(0): Default mode "640x480": 54.0 MHz, 60.0 kHz, 60.0 Hz (D) (**) NVIDIA(0): Default mode "720x400": 35.5 MHz, 37.9 kHz, 85.0 Hz (**) NVIDIA(0): Default mode "576x432": 54.0 MHz, 67.5 kHz, 75.0 Hz (D) (**) NVIDIA(0): Default mode "640x350": 31.5 MHz, 37.9 kHz, 85.1 Hz (**) NVIDIA(0): Default mode "512x384": 47.2 MHz, 68.7 kHz, 85.0 Hz (D) (**) NVIDIA(0): Default mode "512x384": 39.4 MHz, 60.1 kHz, 75.1 Hz (D) (**) NVIDIA(0): Default mode "512x384": 37.5 MHz, 56.5 kHz, 70.1 Hz (D) (**) NVIDIA(0): Default mode "512x384": 32.5 MHz, 48.4 kHz, 60.0 Hz (D) (**) NVIDIA(0): Default mode "512x384": 22.4 MHz, 35.5 kHz, 86.9 Hz (D) (**) NVIDIA(0): Default mode "416x312": 28.6 MHz, 49.7 kHz, 74.7 Hz (D) (**) NVIDIA(0): Default mode "400x300": 28.1 MHz, 53.7 kHz, 85.3 Hz (D) (**) NVIDIA(0): Default mode "400x300": 24.8 MHz, 46.9 kHz, 75.1 Hz (D) (**) NVIDIA(0): Default mode "400x300": 25.0 MHz, 48.1 kHz, 72.2 Hz (D) (**) NVIDIA(0): Default mode "400x300": 20.0 MHz, 37.9 kHz, 60.3 Hz (D) (**) NVIDIA(0): Default mode "400x300": 18.0 MHz, 35.2 kHz, 56.3 Hz (D) (**) NVIDIA(0): Default mode "320x240": 18.0 MHz, 43.3 kHz, 85.2 Hz (D) (**) NVIDIA(0): Default mode "320x240": 15.8 MHz, 37.5 kHz, 75.0 Hz (D) (**) NVIDIA(0): Default mode "320x240": 15.8 MHz, 37.9 kHz, 72.8 Hz (D) (**) NVIDIA(0): Default mode "320x240": 12.6 MHz, 31.5 kHz, 60.1 Hz (D) (**) NVIDIA(0): Default mode "320x200": 15.8 MHz, 37.9 kHz, 85.3 Hz (D) (**) NVIDIA(0): Default mode "320x175": 15.8 MHz, 37.9 kHz, 85.3 Hz (D) (II) NVIDIA(0): Virtual screen size determined to be 1920 x 1200 (--) NVIDIA(0): Display dimensions: (330, 210) mm (--) NVIDIA(0): DPI set to (147, 145) <snip> (II) NVIDIA(0): Setting mode "1920x1200" (II) Loading extension NV-GLX (II) NVIDIA(0): NVIDIA 3D Acceleration Architecture Initialized (II) NVIDIA(0): Using the NVIDIA 2D acceleration architecture (==) NVIDIA(0): Backing store disabled (==) NVIDIA(0): Silken mouse disabled (II) Loading extension NV-CONTROL (==) RandR enabled <snip> (--) Keyboard type: USB (6) (--) Keyboard layout: 33 AUDIT: Mon Oct 17 11:25:36 2005: 1374 Xorg: client 9 rejected from local host AUDIT: Mon Oct 17 11:25:37 2005: 1374 Xorg: client 10 rejected from local host |
|
|
|
 |
| Most Popular NVIDIA Based Graphics Cards | |
|
|
| Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
| Thread Tools | |
|
|
