Noob requires overclocking advice

Logical · 10-08-07, 08:05 AM

I thought it about time i overclocked my system.....but not the GPU.

I have never overclocked this system and a lot of advice is needed...

Everything is set to default in bios except the mem which is set to cpu/overclock 0% This gives my memory a speed of 800mhz at 4-4-4-12 2T, all my HSF's are standard also.

I have read that orthos is a good program for measuring stability after the overclock but what do i use to change the cpu clocks? (there blanked out in bios-using latest bios from evga).

Any help would be much appreciated.

System spec is in sig........

mythy · 10-08-07, 09:10 AM

Don't overclock man. Your not ready yet...

Logical · 10-08-07, 10:02 AM

Hahaha

We'll see

mythy · 10-08-07, 11:06 AM

I don't have a 680i so I am clueless on there bios but look around there should be a option for user defined settings or some thing similar.

Logical · 10-08-07, 11:33 AM

I believe it is the FSB that gives the CPU a higher clock speed.

I found a guide to overclocking C2D on a a680i.....

http://uk.pc.ign.com/articles/747/747606p2.html

mythy · 10-08-07, 11:48 AM

Yes the FSB and its multiplier. But as you raise the FSB you have to watch your ram speed since it will go up as well depending on the buss ratio. But I do belive that on a 680I you can lock the memory's speed to a specific setting such as DDR2 6400 aka "400Mhz X 2"

Logical · 10-08-07, 11:53 AM

Yes part of the overclocking guide explains to set the memory to expert and then unlink everything so i can manually set the timings etc

mythy · 10-08-07, 01:06 PM

Well then good luck let me know when you hit 3.8 GHz or so

**XDanger** · 10-08-07, 02:09 PM

I B Jelous of the unlink

Logical · 10-08-07, 03:34 PM

hehehe 3.8Ghz is a bit high for standard HSF.

I went for a safe core speed of 3Ghz with 1200 FSB, i disabled the SLI memory and unlinked it from the FSB then i manualy set the timings to 4-4-4-12 2T, im sure i could go further with the mem but i had to up the voltage to 2.1v and didnt really wanna go further than that. When i know more about clocking the mem i might consider it.

Ive run Orthos for the last 2.5 hours and it has succesfully completed all the tests upto that time.

CPU temp = 47c idle and 64c underload @ 1.225v

I'm going to look for a aftermarket HSF tommorow and if all is still well at 3Ghz i'll take it further.

andy_nv · 10-08-07, 05:21 PM

After you replace the heatsink you could start upping the voltage in 0.025V increments, but try not to go over 0.20V from default voltage and load temp of 60-65C otherwise it could damage/kill your CPU in time.

BTW, has there been an instance with Core 2 chips like the 'northwood death syndrome' ?

Logical · 10-09-07, 06:25 AM

The scythe ninja rev B looks like a really good HSF and has good reviews.

Has anyone tried one of these yet and can give me an opinion on it ?

10-08-07, 08:05 AM	#1
Logical Registered User Join Date: Apr 2007 Location: UK Posts: 2,510	Noob requires overclocking advice I thought it about time i overclocked my system.....but not the GPU. I have never overclocked this system and a lot of advice is needed... Everything is set to default in bios except the mem which is set to cpu/overclock 0% This gives my memory a speed of 800mhz at 4-4-4-12 2T, all my HSF's are standard also. I have read that orthos is a good program for measuring stability after the overclock but what do i use to change the cpu clocks? (there blanked out in bios-using latest bios from evga). Any help would be much appreciated. System spec is in sig........

10-08-07, 09:10 AM	#2
mythy Single Male Join Date: Dec 2004 Posts: 2,115	Re: Noob requires overclocking advice Don't overclock man. Your not ready yet... __________________ ---Q6600 @3.45 430FSB - P5K Deluxe--- ---1066 5-4-4-12 PL6! - 257 GTX OCed--- ---ASUS Xonar DX - Dell 2407 24 LCD---

10-08-07, 10:02 AM	#3
Logical Registered User Join Date: Apr 2007 Location: UK Posts: 2,510	Re: Noob requires overclocking advice Hahaha We'll see

10-08-07, 11:06 AM	#4
mythy Single Male Join Date: Dec 2004 Posts: 2,115	Re: Noob requires overclocking advice I don't have a 680i so I am clueless on there bios but look around there should be a option for user defined settings or some thing similar. __________________ ---Q6600 @3.45 430FSB - P5K Deluxe--- ---1066 5-4-4-12 PL6! - 257 GTX OCed--- ---ASUS Xonar DX - Dell 2407 24 LCD---

10-08-07, 11:33 AM	#5
Logical Registered User Join Date: Apr 2007 Location: UK Posts: 2,510	Re: Noob requires overclocking advice I believe it is the FSB that gives the CPU a higher clock speed. I found a guide to overclocking C2D on a a680i..... http://uk.pc.ign.com/articles/747/747606p2.html

10-08-07, 11:48 AM	#6
mythy Single Male Join Date: Dec 2004 Posts: 2,115	Re: Noob requires overclocking advice Yes the FSB and its multiplier. But as you raise the FSB you have to watch your ram speed since it will go up as well depending on the buss ratio. But I do belive that on a 680I you can lock the memory's speed to a specific setting such as DDR2 6400 aka "400Mhz X 2" __________________ ---Q6600 @3.45 430FSB - P5K Deluxe--- ---1066 5-4-4-12 PL6! - 257 GTX OCed--- ---ASUS Xonar DX - Dell 2407 24 LCD---

10-08-07, 11:53 AM	#7
Logical Registered User Join Date: Apr 2007 Location: UK Posts: 2,510	Re: Noob requires overclocking advice Yes part of the overclocking guide explains to set the memory to expert and then unlink everything so i can manually set the timings etc

10-08-07, 01:06 PM	#8
mythy Single Male Join Date: Dec 2004 Posts: 2,115	Re: Noob requires overclocking advice Well then good luck let me know when you hit 3.8 GHz or so __________________ ---Q6600 @3.45 430FSB - P5K Deluxe--- ---1066 5-4-4-12 PL6! - 257 GTX OCed--- ---ASUS Xonar DX - Dell 2407 24 LCD---

10-08-07, 02:09 PM	#9
XDanger Whaaat? Join Date: Nov 2005 Posts: 5,674	Re: Noob requires overclocking advice I B Jelous of the unlink __________________ 2500K 4.4ghz,P8P67Pro,120gb Force3, 12gb Vengeance,HD6950,TX850v2,W7HP,LaCie Blue 22" crt COMMODORE 64 Silver Label 1Mhz/128D 4Mhz(Z80)

10-08-07, 03:34 PM	#10
Logical Registered User Join Date: Apr 2007 Location: UK Posts: 2,510	Re: Noob requires overclocking advice hehehe 3.8Ghz is a bit high for standard HSF. I went for a safe core speed of 3Ghz with 1200 FSB, i disabled the SLI memory and unlinked it from the FSB then i manualy set the timings to 4-4-4-12 2T, im sure i could go further with the mem but i had to up the voltage to 2.1v and didnt really wanna go further than that. When i know more about clocking the mem i might consider it. Ive run Orthos for the last 2.5 hours and it has succesfully completed all the tests upto that time. CPU temp = 47c idle and 64c underload @ 1.225v I'm going to look for a aftermarket HSF tommorow and if all is still well at 3Ghz i'll take it further.

10-08-07, 05:21 PM	#11
andy_nv Registered User Join Date: Jan 2005 Posts: 300	Re: Noob requires overclocking advice After you replace the heatsink you could start upping the voltage in 0.025V increments, but try not to go over 0.20V from default voltage and load temp of 60-65C otherwise it could damage/kill your CPU in time. BTW, has there been an instance with Core 2 chips like the 'northwood death syndrome' ?

10-09-07, 06:25 AM	#12
Logical Registered User Join Date: Apr 2007 Location: UK Posts: 2,510	Re: Noob requires overclocking advice The scythe ninja rev B looks like a really good HSF and has good reviews. Has anyone tried one of these yet and can give me an opinion on it ?

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
P4 overclocking - how do you do it?	saturnotaku	CPUs, Motherboards And Memory	1	08-15-02 08:52 AM